[hpsdr] Firmware Update Directory?

[Chris Smith]

Nigel

OK. I think the problem is that the .bat files only know about up to V9.0 SP2 so far. So edit the .bat files to add reference to the location of the V9.1 files.

Chris


On 10 Nov 2009, at 22:54, Nigel Cupitt wrote:

> Hello Chris and Riho
> 
> I did a search and have cmd.exe installed in windows\system32
> 
> I have used TortoiseSVN to download the files from the repositories at svn://206.216.146.154/svn.. That all went ok.
> 
> I started up Altera Quartus and checked in the about section  and I have Version 9.1
> 
> Regards
> 
> Nigel ZL2NBE
> 
> 
> On Wed, Nov 11, 2009 at 11:39 AM, Chris Smith <chris at vspl.co.uk> wrote:
> Nigel
> 
> It's not clear from your email what exactly is going wrong.
> 
> I presume you are using TortoiseSVN to download the files from the repositories at svn://206.216.146.154/svn...
> 
> 
> 
> I keep the firmware updates in the folder C:\PowerSDR Mercury USBBlaster but I'm not sure that they have to be in this exact folder.
> 
> There doesn't appear to be anything in the .bat files which locates the .jic or .cdf files so I suspect that the .bat expects these files to be in the same folder.
> 
> The only files which are specifically located are the  TortoiseSVN to download the files from the repositories at svn://206.216.146.154/svn.. program files which need to be in C:\altera\xy\qprogrammer\bin\quartus_pgm.exe where xy is the version number of the Quartus release you are using i.e. 81, 90, 90sp1 or 90sp2 for versions 8.1, 9.0, 9.0 service pack 1 or 9.0 service pack 2. If the quartus programs are in a different location then the .bat files will need to be edited to reflect the changed location. (I think there may be a version 9.1 available too.)
> 
> Don't know if that helps. Perhaps a copy of the exact error message would be helpful for further diagnosis.
> 
> Cheers
> 
> Chris
> G4NUX
> 
> 
> On 10 Nov 2009, at 21:38, Nigel Cupitt wrote:
> 
> > ***** High Performance Software Defined Radio Discussion List *****
> >
> > Good morning all
> >
> > A quick question
> >
> > When I down load the firmware update files for Penelope and Mercury what directory should these files be in?
> >
> > I have followed the install procedure and all has gone well until now.
> > When I run the batch file I receive the error message path not found, so I guess I have the files in the wrong directory.
> >
> > Thanks in advance
> >
> > Regards
> >
> > Nigel ZL2NBE
> > _______________________________________________
> > HPSDR Discussion List
> > To post msg: hpsdr at openhpsdr.org
> > Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> > HPSDR web page: http://openhpsdr.org
> > Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
> 
> 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/attachments/20091110/4092b48d/attachment-0004.htm>