[hpsdr] PowerSDR_v3.3.6_RA_v1.3_16Feb2016_Release.zip

[georg Prinz]

Good Morning Joe,

I tested your new version with the DCF77-Time-Signal. The Transmitter is 
some 40km near by.

It works perfectly with RX1, RX2 and even with both receivers. You can 
change the resolution of the
display during receptions, too. Now you can visually analize the 
received signal, too.
This exactly what I was looking for.

Thank You for Your fantastic work and the fast response.

Have a nice day and best Regards from Germany.

Georg,
dl2kp


Am 17.02.2016 um 02:29 schrieb Joe Martin:
> ***** High Performance Software Defined Radio Discussion List *****
>
> Opps, sorry, the download link is actually:
>
> http://www.k5so.com/PowerSDR_v3.3.6_RA_v1.3_16Feb2016_Release.zip
>
> 73, Joe K5SO
>
> On Feb 16, 2016, at 6:23 PM, Joe Martin wrote:
>
>> ***** High Performance Software Defined Radio Discussion List *****
>>
>> RA users:
>>
>> PowerSDR_v3.3.6_RA_v1.3_16Feb2016_Release.zip is available for download at
>>
>> http://www.k5so.com/PowerSDR_v3.3.6_RA_v1.3_16Feb2016.zip
>>
>> This is a modified version of PowerSDR mRX PS v3.3.6 that includes an enhanced version of the RA (Radio Astronomy) utility.  Specific new changes to this RA utility version are:
>>
>> 1) Expanded data size options for writing to disk, including new limits for the maximum time scale for display (up to 100,000 seconds of recording and display).
>>
>> 2) Increased maximum number of data points stored/collected from the previous 10,000 points to 2,000,000 points now.
>>
>> 3) The two increased limits above permit over 27 hours of continuous data collection at the highest (50 mSec/point) data recording rate for dual channels.
>>
>> 4) Fixed the file read problem previously reported.
>>
>> 5) Changed the data file header format to a ten line header as follows:
>>
>> 	(1) RA version information
>> 	(2) blank
>> 	(3) Date/Time of the acquisition
>> 	(4) blank
>> 	(5) Comment line that the user can use as he wishes to identify the data in the file, etc.
>> 	(6) blank
>> 	(7) Parameter description for line 8: “mSec between measurements, number of measurement averaged per point”
>> 	(8) Parameters for (7) above
>> 	(9) blank
>> 	(10) Data format description (i.e., Time (seconds), RX1 signal (dBm), RX2 signal (dBm))
>>
>> 6) Added updating of the “mSec between measurements” control and “number of measurements averaged per point” control on the RA display upon a file READ
>>
>> 7) Added display of the Date/Time and Comment information to the RA display on a file READ
>>
>> 8) Added Global Region support for the utility
>>
>> I hope these new features increase the versatility of the RA utility sufficiently to satisfy most users requirements.
>>
>> Please let me know if you happen to notice a problem with it.  If I don’t hear of problems in the next few days I’ll pass the source code for this new RA utility version to Doug for inclusion in the next public release of OpenHPSDR PowerSDR.
>>
>> Thank you all for your suggestions and help in testing the RA utility!
>>
>> 73, Joe K5SO
>>
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>


---
Diese E-Mail wurde von Avast Antivirus-Software auf Viren geprüft.
https://www.avast.com/antivirus