[hpsdr] Hermes, no Firmware Update possibile

Fri Feb 9 11:06:01 PST 2018

Hi.

I do not know how many times I have used the Bootloader to load and reload  
the firmware to Hermes and other OpenHPSDR boards and I can not remember  
that the boards was not found except when the board was faulty. But I  
always use a dumb switch between the board and the PC. Try that just to be  
sure.

På Fri, 09 Feb 2018 19:38:48 +0100, skrev Chris DG8DP <om.chris at dg8dp.de>:

> ***** High Performance Software Defined Radio Discussion List *****
>
> Hi,
>
> ok I tried it again minutes ago...
>
> 1.
> checked my network settings from the PC 192.168.10.3 / 255.255.255.0
> Disable the 2nd Network (WiFi)
> Disable the Firewall
> 2.
> checked the IP from the board 192.168.10.2
> 3.
> start PowerSDR, works fine
> 4.
> switched of the PC and the board.
> 5.
> restart both, first I start the board, then the PC
> 6.
> start the Programmer as Admin and press "Discover"
> 7.
> Board comes back with MAC, right IP and Version 3.1
> 8.
> Load again the rbf from Github and press Program
> 9.
> In status Monitor I see first erasing, programming 20% to 100% and then  
> the board starts again and disover...
> 10.
> It is the Version 3.1 shown!!!
> 11.
> Switch of the Board, switch on, discover... Version 3.1 is shown
>
> I can see that there is traffic on the network LED so there is an DATA  
> transfer to the board.
> OK start again with a try for Bootlader
>
> 6.
> set J12 (yes, I measured also the Jumper, works, hihi)
> 7.
> start Bootloader as Admin
> 8.
> press "Test for bootloader"
> Nothing is happening!!!
> The board is not answering...
>
> If I read right Bootloader use UDP, so no reason why I got no  
> information from the board
> The Programmer use RAW packages to get the MAC, that works but no  
> success after writing.
>
> Why is the Bootloader not getting the MAC Address?
> No switches, direct wiring, different cables tested!
>
> Vy 73 de DG8DP
> Chris
>
> www.dg8dp.de
>
> -----Ursprüngliche Nachricht-----
> Von: Hpsdr [mailto:hpsdr-bounces at lists.openhpsdr.org] Im Auftrag von  
> Helmut Oeller
> Gesendet: Freitag, 9. Februar 2018 17:15
> An: 'Joe Martin' <k5so at k5so.com>; 'Kjell Karlsen' <la2ni at online.no>
> Cc: hpsdr at lists.openhpsdr.org
> Betreff: Re: [hpsdr] Hermes, no Firmware Update possibile
>
> ***** High Performance Software Defined Radio Discussion List *****
>
> Hi guys,
>
> Maybe that's a little deficit that the  firmware link (only) for Hermes  
> on the openHPSDR site is not updated, but there is also a link to  
> https://github.com/TAPR/ on that site.
> Again both tools - HPSDR Programmer and HPSDR Bootloader - can be used  
> to change to Hermes v3.3 rbf and work.
>
> 73, Helmut, DC6NY
>
> -----Ursprüngliche Nachricht-----
> Von: Hpsdr [mailto:hpsdr-bounces at lists.openhpsdr.org] Im Auftrag von Joe  
> Martin
> Gesendet: Freitag, 9. Februar 2018 16:06
> An: Kjell Karlsen <la2ni at online.no>
> Cc: hpsdr at lists.openhpsdr.org
> Betreff: Re: [hpsdr] Hermes, no Firmware Update possibile
>
> ***** High Performance Software Defined Radio Discussion List *****
>
> Hi Kjell,
>
> Yes, I too ALWAYS use bootloader mode to change firmware in any of the  
> OpenHPSDR/Apache Labs platforms, as like you, I find the various HPSR  
> Programmer programs much less reliable.  Bootloader always works simply  
> and flawlessly.
>
> I can’t speak to the OpenHPSDR site links.  I personally always search  
> for any software/firmware versions on the GitHub repository.
>
> 73, Joe K5SO
>
>> On Feb 9, 2018, at 7:49 AM, Kjell Karlsen <la2ni at online.no> wrote:
>>
>> ***** High Performance Software Defined Radio Discussion List *****
>>
>> Hi Joe.
>>
>> I have not seen the information about this upgrade and when I searched  
>> for it on the OpenHPSDR site I found nothing pointing to Github for  
>> Hermes firmware and the same when I searched on Apache Labs.
>>
>> I downloaded and used Bootloader programmer to upgrade and it worked OK  
>> on the first attempt.
>>
>> I prefer to use the Bootloader for programming as I have never had any  
>> problems with it. The HPSDR Programmer can be a bit tricky to use.
>>
>> 73, Kjell
>>
>>
>>
>>
>>
>>
>> På Fri, 09 Feb 2018 15:21:51 +0100, skrev Joe Martin <k5so at k5so.com>:
>>
>>> ***** High Performance Software Defined Radio Discussion List *****
>>>
>>> Chris,
>>>
>>> Perhaps you are downloading the .rbf file incorrectly from the GitHub  
>>> site?  Use:
>>>
>>> https://github.com/TAPR/OpenHPSDR-Firmware/blob/master/Protocol%201/Hermes/Hermes_v3.3.rbf
>>>
>>> Be sure to click on the “Download” button at the above URL.  DO NOT  
>>> use “Save As” from your browser.  Then after the download completes  
>>> ensure that the file size shows as 649 KB.  If you do use the download  
>>> button the file size will be much smaller and the file will not be the  
>>> file you intended to download. Several people have fallen prey to that  
>>> trap before;  just thought I’d remind you about it.
>>>
>>> 73, Joe K5SO
>>>
>
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help:  
> http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help:  
> http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help:  
> http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/

-- 
Sendt med Operas e-postklient: http://www.opera.com/mail/