<div dir="ltr"><br><br><div class="gmail_quote">2008/6/29 Dominic Hawken <span dir="ltr"><<a href="mailto:dominic@del.co.uk">dominic@del.co.uk</a>></span><br><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
***** High Performance Software Defined Radio Discussion List *****<br>
<br>
Hi All,<br>
<br>
Many, many thanks for the power suppy info - am wiring it all up now :-)<br>
<br>
Thanks again.<br>
<br>
Dominic.<br>
<br>
----- Original Message ----- From: "Eric Ellison" <<a href="mailto:ecellison@gmail.com" target="_blank">ecellison@gmail.com</a>><br>
To: "'Dominic Hawken'" <<a href="mailto:dominic@del.co.uk" target="_blank">dominic@del.co.uk</a>>; <<a href="mailto:hpsdr@hpsdr.org" target="_blank">hpsdr@hpsdr.org</a>><br>
Sent: Saturday, June 28, 2008 4:34 PM<br>
Subject: RE: [hpsdr] power supply for hpsdr<br>
<br>
<br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
Dominic / All<br>
<br>
Power supplies for Atlas have been discussed many times and board current<br>
measurements (except for Mercury at the moment) have been posted. No problem<br>
for bringing it up again. The design of Atlas to use a standard ATX<br>
connector and place boards on PC slot spacing for 'cabinet' purposes were<br>
discussed extensively prior to Phil Covington finalizing Atlas.. Check the<br>
HPSDR archives all the way back to Xylo Group for earlier work on Power and<br>
Atlas design.<br>
<br>
There are numerous articles posted on the Web for using and taming ATX power<br>
supplies for bench supply use. Note on most supplies (Not PicoPSU) you will<br>
need a 10 ohm 10 watt resistor in the 5 volt line to provide load to keep<br>
power on the outputs.<br>
<br>
Just one example:<br>
<br>
<a href="http://www.mbeckler.org/powersupply.html" target="_blank">http://www.mbeckler.org/powersupply.html</a></blockquote></blockquote><div> </div><div>good link is <a href="http://www.mbeckler.org/powersupply/">http://www.mbeckler.org/powersupply/</a> <br>
<br></div><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;"><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
<a href="http://www.mbeckler.org/powersupply.html" target="_blank"></a><br>
<br>
Also Scotty - WA2DFI TAPR has extensively used the PicoPSU to power and test<br>
the various boards. The Pico PSU was somewhat crudely tested in the early<br>
going and found to be pretty quiet on the buss. If I remember correctly<br>
there was some short range 'radiated' rf noise. So far it handles a<br>
reasonable number of boards. Mercury will probably bring a new definition to<br>
the word Sensitivity, and Phil Harman and other alpha testers will be<br>
testing the Mercury Alpha with PicoPSU to see if there are any issues. Since<br>
the 5 Mercury Alpha's are on the way to the testers, we should know in a<br>
week.<br>
<br>
<a href="http://www.mini-box.com/s.nl/it.A/id.417/.f" target="_blank">http://www.mini-box.com/s.nl/it.A/id.417/.f</a><br>
<br>
<br>
Many HPSDR nuts are using bench supplies.<br>
<br>
There is no Standard Supply or recommended supply at this point.<br>
<br>
Thanks<br>
Eric - AA4SW<br>
<br>
<br>
<br>
-----Original Message-----<br>
From: <a href="mailto:hpsdr-bounces@lists.hpsdr.org" target="_blank">hpsdr-bounces@lists.hpsdr.org</a> [mailto:<a href="mailto:hpsdr-bounces@lists.hpsdr.org" target="_blank">hpsdr-bounces@lists.hpsdr.org</a>]<br>
On Behalf Of Dominic Hawken<br>
Sent: Friday, June 27, 2008 8:25 PM<br>
To: <a href="mailto:hpsdr@hpsdr.org" target="_blank">hpsdr@hpsdr.org</a><br>
Subject: [hpsdr] power supply for hpsdr<br>
<br>
***** High Performance Software Defined Radio Discussion List *****<br>
<br>
Apologies if this has been covered before - have googled etc.<br>
<br>
Is there a current preferred psu to use for Atlas etc? Am about to plug<br>
in my home-assembled Atlas and all available boards but slightly scared<br>
I might blow the whole thing with a bad solder joint. All looks good but<br>
recent mention of 'over-voltage' protection etc makes me a little scared<br>
of using a standard PC psu / flicking the on switch.<br>
<br>
What's the current psu of choice for you guys that have up and running<br>
systems?<br>
<br>
Dominic - G6NQO<br>
<br>
-- <br>
Director<br>
Deluxe Corporation Ltd<br>
<a href="http://www.del.co.uk/" target="_blank">http://www.del.co.uk/</a><br>
_______________________________________________<br>
HPSDR Discussion List<br>
To post msg: <a href="mailto:hpsdr@hpsdr.org" target="_blank">hpsdr@hpsdr.org</a><br>
Subscription help: <a href="http://lists.hpsdr.org/listinfo.cgi/hpsdr-hpsdr.org" target="_blank">http://lists.hpsdr.org/listinfo.cgi/hpsdr-hpsdr.org</a><br>
HPSDR web page: <a href="http://hpsdr.org" target="_blank">http://hpsdr.org</a><br>
Archives: <a href="http://lists.hpsdr.org/pipermail/hpsdr-hpsdr.org/" target="_blank">http://lists.hpsdr.org/pipermail/hpsdr-hpsdr.org/</a><br>
<br>
<br>
</blockquote>
<br>
_______________________________________________<br>
HPSDR Discussion List<br>
To post msg: <a href="mailto:hpsdr@hpsdr.org" target="_blank">hpsdr@hpsdr.org</a><br>
Subscription help: <a href="http://lists.hpsdr.org/listinfo.cgi/hpsdr-hpsdr.org" target="_blank">http://lists.hpsdr.org/listinfo.cgi/hpsdr-hpsdr.org</a><br>
HPSDR web page: <a href="http://hpsdr.org" target="_blank">http://hpsdr.org</a><br>
Archives: <a href="http://lists.hpsdr.org/pipermail/hpsdr-hpsdr.org/" target="_blank">http://lists.hpsdr.org/pipermail/hpsdr-hpsdr.org/</a><br>
</blockquote></div><br><br clear="all"><br>-- <br><br>73! de Standa OK1VSH<br>RadioClub Vodnany OK1KFB<br><br>
</div>