<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=US-ASCII">
<META content="MSHTML 6.00.2900.2180" name=GENERATOR></HEAD>
<BODY id=role_body style="FONT-SIZE: 10pt; COLOR: #000000; FONT-FAMILY: Arial" bottomMargin=7 leftMargin=7 topMargin=7 rightMargin=7><FONT id=role_document face=Arial color=#000000 size=2>
<DIV>I recall a problem with one of the versions on initial start up. It did not
like</DIV>
<DIV>the selection of a "transverter" being present. So try deleting the
Powersdr.mdb</DIV>
<DIV>file and when you start for the first time, do NOT select that you have a
transverter</DIV>
<DIV>or a PA, but make sure you select HPSDR Janus/Ozy (USB2) in the sound
card</DIV>
<DIV>pull down. You can do the others later. Also before you click the
start button, go </DIV>
<DIV>to setup and under options select "disable PTT", and under Hardware
Config,</DIV>
<DIV>select Janus/Ozy Control. </DIV>
<DIV> </DIV>
<DIV>Also be sure that you have the proper USBIO.exe loaded and .2
NetFramework.</DIV>
<DIV> </DIV>
<DIV>Cycle power on the atlas bus, then Click on PowerSDR.exe, during the
initialization</DIV>
<DIV>you should NOT see any errors, such as "Error Initializing Ozy; Control has
been </DIV>
<DIV>disabled". If the PowerSDR control panel comes up with NO errors, before
you</DIV>
<DIV>click "Start" go to Setup> General> Hardware Config and make sure
that Janus/Ozy</DIV>
<DIV>control is checked.</DIV>
<DIV> </DIV>
<DIV>If this all works, you should NOT have to repeat the procedure. You can
then check</DIV>
<DIV>the receive out, then enable PTT and check PA present etc.</DIV>
<DIV> </DIV>
<DIV>73 and good luck</DIV>
<DIV> </DIV>
<DIV>Joe K1RQG</DIV>
<DIV> </DIV>
<DIV>
<DIV>In a message dated 6/15/2011 5:52:49 P.M. Eastern Daylight Time,
hb9ajp@besonet.ch writes:</DIV>
<BLOCKQUOTE style="PADDING-LEFT: 10px; MARGIN-LEFT: 10px"><FONT style="BACKGROUND-COLOR: transparent" face=Arial color=#000000 size=2>*****
High Performance Software Defined Radio Discussion List *****<BR><BR>Hi
all<BR><BR>to my recent post describing my problem getting SDR-1000 with
JanusOzy running, I got many hints and ideas from list members. I tried all of
them and I am very grateful for this engagement.<BR><BR>The situation now is
the following: Intozy11.bat loads fine (mostly) and PSDR can be loaded and the
SDR-1000 relays are clicking. When I check the Janus/Ozy Control box in the
Setup/General/Hardware Config menu it is normally accepted (sometimes an Ozy
Initialization Error occurs). But when I start PSDR the system does not
receive and there is only a straight line displayed in the panadapter and no
audio. Sometimes the system goes into transmit mode. The leds D2 and D3 (D4 in
transmit) on the Ozy board stay dark. <BR><BR>When I use the M-Audio Delta 44
sound card instead of Janus the system works alright with SDR-1000. Also when
I additionally install Mercury I can start PSDR in the HPSDR mode and
everything works fine. Therefore the idea arose that there might be something
wrong with Janus. I have checked the jumpers on the board and read all
Janus/Ozy postings in the archive but could not find an idea how to
proceed.<BR><BR>Any hints are appreciated. (PC software is WinXP).<BR><BR>73,
Chris HB9AJP<BR>_______________________________________________<BR>HPSDR
Discussion List<BR>To post msg: hpsdr@openhpsdr.org<BR>Subscription help:
http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org<BR>HPSDR web page:
http://openhpsdr.org<BR>Archives:
http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/<BR></FONT></BLOCKQUOTE></DIV></FONT></BODY></HTML>