Roland,<div><br></div><div>I use a fine tipped  syringe to put the solder paste onto the pads  Works well for 0603 and even 0402 sized components, but tends to put down too much paste for  fine pitch parts (which I just clean up after reflow).  I, too, use a toaster oven to make the UHF and VHF beacons and APRS transmitters that I sell.  I hear that a convection oven is better than a non-convection oven.  I line the tray in my (cheap) oven with ceramic floor tiles to even out the heat.</div>
<div><br></div><div>As far as hot air pencil goes, I got mine from SparkFun -- about $100 and works very well, especially for removing parts.</div><div><br></div><div><a href="http://www.sparkfun.com/products/10706">http://www.sparkfun.com/products/10706</a>
</div><div><br></div><div><br></div><div>-Greg Clark K7RKT <a href="http://www.bigredbee.com">http://www.bigredbee.com</a></div><div><br><div class="gmail_quote">On Thu, Mar 8, 2012 at 1:16 PM, Chris Albertson <span dir="ltr"><<a href="mailto:albertson.chris@gmail.com">albertson.chris@gmail.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div class="im">***** High Performance Software Defined Radio Discussion List *****<br>
<br>
</div>On Thu, Mar 8, 2012 at 12:45 PM, roland etienne <<a href="mailto:roland.etienne@free.fr">roland.etienne@free.fr</a>> wrote:<br>
<br>
> I’ve been lucky to get an Hermes PCB, and I am now collecting all the components. I am wondering what is your favourite method to solder all the ICs and oscillators: iron, hot air or refusion oven ?<br>
><br>
> Surely, I will buy an hot air station, any model recommended ?<br>
><br>
> I would like to make some test with a refusion oven, any advice? Is it possible to do several passes ?<br>
<br>
There is an endless supply of test material for experimenting with an<br>
oven.  Just take apart any dead consumer device like an old VCR or<br>
computer. Heat the pcb and tap it on the table top and parts will rain<br>
down. (tap them into a baking pan or they tiny parts will bounce onto<br>
the floor and you will never find them.)  Then you have a (nearly)<br>
blank PCB and parts, what more would you need for practice?<br>
<br>
I think if you are going to build a complex PCB in a reflow oven you'd<br>
need a stencil and solder paste.   Without the sticky paste you'd<br>
shake the parts of their pads.<br>
<span class="HOEnZb"><font color="#888888"><br>
Chris Albertson<br>
Redondo Beach, California<br>
_______________________________________________<br>
HPSDR Discussion List<br>
To post msg: <a href="mailto:hpsdr@openhpsdr.org">hpsdr@openhpsdr.org</a><br>
Subscription help: <a href="http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org" target="_blank">http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org</a><br>
HPSDR web page: <a href="http://openhpsdr.org" target="_blank">http://openhpsdr.org</a><br>
Archives: <a href="http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/" target="_blank">http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/</a><br>
</font></span></blockquote></div><br></div>