<p dir="ltr">Hi Phil !</p>
<p dir="ltr">The Fuses are the 2 A ones and they are ok. </p>
<p dir="ltr">73 Oliver DL6KBG</p>
<div class="gmail_quote">Am 19.02.2013 02:07 schrieb "Phil Harman" <<a href="mailto:phil@pharman.org">phil@pharman.org</a>>:<br type="attribution"><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Hi Oliver,<br>
<br>
Check F3, on early BOMs it was 1A but was increased to 2A on later versions.<br>
<br>
73 Phil..VK6APH<br>
<br>
<br>
<br>
<br>
> ***** High Performance Software Defined Radio Discussion List *****<br>
><br>
> Hi All !<br>
><br>
> I am having a problem since sunday. I am not making progress in debugging<br>
> the error. Hermes ran nearly the whole weekend during the contest. The<br>
> enclosure was warm but not hot.<br>
><br>
> The problem:<br>
><br>
> The board starts fine es every time and i can run it for lets say  one<br>
> minute with cuSDR64, ghpsdr3. After the minute the leds are only showing<br>
> half of the light than before. the board is then no more reachable and<br>
> cannot be discovered. When i start the board  in bootloader mode<br>
> everything<br>
> is normal. When i remove the jumper and powercycle the board it runs also<br>
> fine just to the time i put the networkcable in. it seems that network<br>
> traffic can speed up that failure.<br>
><br>
> I measured as follows:<br>
><br>
> U18, PIN3 = 13,6 Volt<br>
> U18, PIN2 = 11,9 Volt<br>
><br>
> in normal operation and after shutdown.<br>
><br>
> The SMPS 5V output shows 4,96 V also in normal conditions and after the<br>
> shutdown (measured at L32). So i think the 12V and 5V Buses are ok ?!<br>
><br>
> Now i measured at C153 and C174 and the input Pin of the LTC1529. During<br>
> the normal operation i have 4,45 Volt there. During the minute until the<br>
> shutdown the Voltage decreases down to 2,83 Volt in 0,01 Volt steps. The<br>
> last steps are faster.<br>
><br>
> When i understand the schematics right i should have the same voltage at<br>
> the end of L32 and at C153.<br>
><br>
> This must be something serious or silly. I hope the last one.<br>
><br>
> In bootloader mode i am able to program and successfully reprogrammed the<br>
> board back to 2.2 which results in the same behaviour.<br>
><br>
> 73 Oliver DL6KBG<br>
> _______________________________________________<br>
> HPSDR Discussion List<br>
> To post msg: <a href="mailto:hpsdr@openhpsdr.org">hpsdr@openhpsdr.org</a><br>
> Subscription help:<br>
> <a href="http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org" target="_blank">http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org</a><br>
> HPSDR web page: <a href="http://openhpsdr.org" target="_blank">http://openhpsdr.org</a><br>
> Archives: <a href="http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/" target="_blank">http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/</a><br>
<br>
<br>
</blockquote></div>