<br><br><div class="gmail_quote">On Thu, Mar 14, 2013 at 3:12 PM, Mike Monnier <span dir="ltr"><<a href="mailto:w8bac@comcast.net" target="_blank">w8bac@comcast.net</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<u></u>



<div style="PADDING-LEFT:10px;PADDING-RIGHT:10px;PADDING-TOP:15px" name="Compose message area">
<div>
<div>"There was a bad value in the Schmidt-trigger squaring circuit for the 
10MHz reference input. R141, the emitter resistor of the differential pair, has 
the wrong value. It should be 50Ω, not 100Ω. Change that an you won't have any 
problems with using your external reference. "</div>
<div><font face="Calibri"></font> </div>
<div><font face="Calibri">I see some odd type from time to time on this reflector. 
In your post (cut and pasted above) you are talking about R 141. A resistor I 
assume and it should be 50 ohm? Not 100 ohm? Is that right? </font></div></div></div></blockquote><div><br></div><div>Yes, yes, and yes.</div><div> </div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div style="PADDING-LEFT:10px;PADDING-RIGHT:10px;PADDING-TOP:15px" name="Compose message area"><div><div><font face="Calibri">I am not able to 
replace an SMT component on a 5 layer board. </font></div></div></div></blockquote><div><br></div><div>Why not? Hot-air rework tools are pretty cheap now. This is what I used:</div><div><br></div><div><a href="http://www.circuitspecialists.com/csihotgun-2.html">http://www.circuitspecialists.com/csihotgun-2.html</a></div>
<div><br></div><div>You can't go too far wrong for $89. </div><div><br></div><div>Heat up the resistor with the hot-air rework tool; remove the resistor with tweezers; use an iron and solder wick to get rid of that wicked, nasty RoHS solder crap; put down a couple of dabs of good PbSn solder paste; heat again with the hot-air tool; put it all back together; and go play radio.</div>
<div> </div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div style="PADDING-LEFT:10px;PADDING-RIGHT:10px;PADDING-TOP:15px" name="Compose message area"><div><div><font face="Calibri">I'll have to think about this. 
What is the power rating of R141? I may have to find a SMT tech to do this for 
me. I have two Anan-10 rigs. They both will need the modification.</font></div></div></div></blockquote><div><br></div><div>It doesn't dissipate any power to speak of. Use the same size component. </div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div style="PADDING-LEFT:10px;PADDING-RIGHT:10px;PADDING-TOP:15px" name="Compose message area"><div><div><font face="Calibri"> </font></div>
<div> </div>
<div><font face="Calibri">Your reply is exactly what I was looking for Brian. 
Thank You Very Much for your help.</font></div></div></div></blockquote><div><br></div><div>You are welcome.</div><div><br></div></div>-- <br>Brian Lloyd, WB6RQN/J79BPL<br>3191 Western Dr.<br>Cameron Park, CA 95682<br><a href="mailto:brian@lloyd.com" target="_blank">brian@lloyd.com</a><br>
+1.767.617.1365 (Dominica)<br>+1.916.877.5067 (USA)<br>