<html><body><div style="color:#000; background-color:#fff; font-family:tahoma, new york, times, serif;font-size:10pt"><br><div style="font-family: tahoma, new york, times, serif; font-size: 10pt;"><div style="font-family: times new roman, new york, times, serif; font-size: 12pt;"><br><div class="y_msg_container"><div id="yiv1589141340"><div><div style="color:#000;background-color:#fff;font-family:tahoma, new york, times, serif;font-size:10pt;"><div><span>You could also look at http://g4hup.com/DA/DA.htm. Available as kit or built and tested<br></span></div><div style="color:rgb(0, 0, 0);font-size:13.3333px;font-family:tahoma, new york, times, serif;background-color:transparent;font-style:normal;"><br><span></span></div><div style="color:rgb(0, 0, 0);font-size:13.3333px;font-family:tahoma, new york, times, serif;background-color:transparent;font-style:normal;"><span>73,</span></div><div style="color:rgb(0, 0,
0);font-size:13.3333px;font-family:tahoma, new york, times, serif;background-color:transparent;font-style:normal;"><span>Dave, G4HUP</span></div><div><br></div> <div style="font-family:tahoma, new york, times, serif;font-size:10pt;"> <div style="font-family:times new roman, new york, times, serif;font-size:12pt;"> <div dir="ltr"> <hr size="1">
<font face="Arial" size="2"> <b><span style="font-weight:bold;">From:</span></b> Chris Wilson <chris@chriswilson.tv><br> <b><span style="font-weight:bold;">To:</span></b> hpsdr <hpsdr@lists.openhpsdr.org> <br> <b><span style="font-weight:bold;">Sent:</span></b> Saturday, 18 May 2013, 22:13<br> <b><span style="font-weight:bold;">Subject:</span></b> Re: [hpsdr] external 10MHz reference input<br> </font> </div> <div class="yiv1589141340y_msg_container"><br>***** High Performance Software Defined Radio Discussion List *****<br><br><br><br>> ***** High Performance Software Defined Radio Discussion List *****<br><br>> Hi Bert, <br><br>> RR, understood. <br><br>> Here I use a TAPR TADD distribution amp between my Rb-vapor freq<br>> standard output and the ext 10 MHz input on my radios. Perhaps you<br>> need a bit more in terms of drive for the ext 10 MHz input on your Hermes boards?<br><br>> Keep in mind the 3.3v
limit on
the board devices, as has been mentioned.<br><br>> Good luck! <br><br>> 73, Joe K5SO<br><br><br><br>18/05/2013 22:12<br><br>Hi Joe, can you tell me if these distribution amps are still<br>available? I am now at a point where I have more test gear and stuff<br>than I can realistically daisy chain from my Trimble Thunderbolt GPS<br>locked source without a distribution amp. I seem to recall seeing this<br>was discontinued, but not sure. Thanks!<br><br>-- <br> Best Regards,<br> Chris Wilson.<br><br>_______________________________________________<br>HPSDR Discussion List<br>To post msg: <a rel="nofollow" ymailto="mailto:hpsdr@openhpsdr.org" target="_blank" href="mailto:hpsdr@openhpsdr.org">hpsdr@openhpsdr.org</a><br>Subscription help: <a rel="nofollow" target="_blank"
href="http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org">http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org</a><br>HPSDR web
page: <a rel="nofollow" target="_blank" href="http://openhpsdr.org/">http://openhpsdr.org</a><br>Archives: <a rel="nofollow" target="_blank" href="http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/">http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/</a><br><br><br></div> </div> </div> </div></div></div><meta http-equiv="x-dns-prefetch-control" content="on"><br><br></div> </div> </div> </div></body></html>