<div dir="ltr">Mine is revision B and has a huge power switch installed. You can't miss it.  I remember there was an option to put jumpers and bypass the switch installation.  Are five power supply LEDs ON? If so then you should be all set as far as powering up the board .  I have these jumpers on: J18, J17 (the two pins closer to the network jack) J21 J20 J26.  13.8 V power supply..</div>

<div class="gmail_extra"><br><br><div class="gmail_quote">On Tue, Nov 5, 2013 at 9:39 PM, Anupam Prasad <span dir="ltr"><<a href="mailto:anupam@ancorlabs.org" target="_blank">anupam@ancorlabs.org</a>></span> wrote:<br>

<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">***** High Performance Software Defined Radio Discussion List *****<br>
<br>
Dear all,<br>
<br>
I got a new Rev B Hermes board from TAPR. The problem is that I have not<br>
been able to start-up the Hermes at all.  I am following the instructions<br>
laid out in these documents.<br>
                a.  Schematic revision Gamma 15 .<br>
(<a href="http://www.k9ivb.net/hermes/HERMES_PROD_SCHEMATICS[gama_v18_10-09-2012].pdf" target="_blank">http://www.k9ivb.net/hermes/HERMES_PROD_SCHEMATICS[gama_v18_10-09-2012].pdf</a><br>
)<br>
                b. Hermes User manual V 1.17.<br>
(<a href="http://svn.tapr.org/repos_sdr_hpsdr/trunk/Hermes/Documentation/Hermes_User_" target="_blank">http://svn.tapr.org/repos_sdr_hpsdr/trunk/Hermes/Documentation/Hermes_User_</a><br>
Manual_V1.17.pdf)<br>
                c. Startup Hermes V1.1 instructions.<br>
(<a href="http://svn.tapr.org/repos_sdr_hpsdr/trunk/Hermes/Documentation/Startup_Herm" target="_blank">http://svn.tapr.org/repos_sdr_hpsdr/trunk/Hermes/Documentation/Startup_Herm</a><br>
es_V1.1.pdf )<br>
<br>
But following have come to light.<br>
1.      The Schematic and Manual both speak about a power switch. There is<br>
none on the Rev B board.<br>
2.      The DC input Pins are also different in the schematic and the<br>
manual. What is it on the actual board ?<br>
<br>
Is there  anything that I am missing? Do I have the latest documents ? Are<br>
there any corrections that to be made in the Schematics?<br>
<br>
Warm Regards,<br>
<br>
Anupam Prasad <a href="tel:%28%2B91%207838598510" value="+917838598510">(+91 7838598510</a>)<br>
<br>
Ancor Research Labs LLP<br>
Level 12, Tower C, Building 8<br>
DLF Cyber City Complex<br>
DLF Phase II<br>
Gurgaon 122 002<br>
Haryana, India<br>
<br>
<br>
<br>
_______________________________________________<br>
HPSDR Discussion List<br>
To post msg: <a href="mailto:hpsdr@openhpsdr.org">hpsdr@openhpsdr.org</a><br>
Subscription help: <a href="http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org" target="_blank">http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org</a><br>
HPSDR web page: <a href="http://openhpsdr.org" target="_blank">http://openhpsdr.org</a><br>
Archives: <a href="http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/" target="_blank">http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/</a><br>
</blockquote></div><br></div>