<div dir="ltr">Bob;<div>That's exactly what I did; works and looks fine.</div><div>73,</div><div>Dan, W0IQ</div></div><div class="gmail_extra"><br><br><div class="gmail_quote">On Thu, Nov 21, 2013 at 2:54 PM, Bob Campbell <span dir="ltr"><<a href="mailto:joan-bob@bigpond.net.au" target="_blank">joan-bob@bigpond.net.au</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">***** High Performance Software Defined Radio Discussion List *****<br>
<br>
Hi to all,<br>
<br>
I elected to put 3 of the caps down in place of the originals first and<br>
then the fourth on top of the middle one with an extra dose of solder on<br>
the ends.  So far its performing well and looks neat as well.<br>
73's<br>
Bob.c<br>
Vk4xv<br>
<br>
On Thu, 2013-11-21 at 06:55 -0600, John wrote:<br>
> What is the best way to install the four new<br>
> capacitors that replace C25 C26 C27?<br>
><br>
> Is it better to stack one on top of another or<br>
> try to stagger them across the existing pads?<br>
> Or maybe stagger the one stacked on top so that<br>
> it makes contact with two of the bottom capacitors?<br>
><br>
> Best regards,<br>
><br>
> John,  WoGN<br>
><br>
><br>
><br>
><br>
> At 03:30 AM 11/16/2013, Kjell Karlsen wrote:<br>
> >***** High Performance Software Defined Radio Discussion List *****<br>
> ><br>
> >Hi Al.<br>
> ><br>
> >I agree that the problem might be one of the capacitors. All my problems<br>
> >with low power on 6 meter has been with the output transformer and<br>
> >components around it.<br>
> ><br>
> >Please report back when you have tested with new capacitors.<br>
> ><br>
> >73, Kjell<br>
> ><br>
> ><br>
> ><br>
> ><br>
> ><br>
> >På Sat, 16 Nov 2013 00:33:28 +0100, skrev Bob Campbell<br>
> ><<a href="mailto:joan-bob@bigpond.net.au">joan-bob@bigpond.net.au</a>>:<br>
> ><br>
> >>***** High Performance Software Defined Radio Discussion List *****<br>
> >><br>
> >>Hi Al,<br>
> >><br>
> >>Check caps C25 C26 C27 are all ok.<br>
> >><br>
> >>Mine failed when I went to load it up on 6m, blew the cermic cap apart.<br>
> >><br>
> >>As Kjell suggested in a previous post replace these caps with four 220pf<br>
> >>500vw 1206 caps.  Since doing this mine has been ok.  I suspect with<br>
> >>this mod the current is shared evenly between all 4 caps and the circuit<br>
> >>is much more stable and I have no trouble getting the desired output on<br>
> >>6m now.<br>
> >><br>
> >>73's<br>
> >>Bob.c<br>
> >>Vk4xv<br>
> >><br>
> >>_______________________________________________<br>
><br>
><br>
<br>
<br>
_______________________________________________<br>
HPSDR Discussion List<br>
To post msg: <a href="mailto:hpsdr@openhpsdr.org">hpsdr@openhpsdr.org</a><br>
Subscription help: <a href="http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org" target="_blank">http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org</a><br>
HPSDR web page: <a href="http://openhpsdr.org" target="_blank">http://openhpsdr.org</a><br>
Archives: <a href="http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/" target="_blank">http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/</a></blockquote></div><br></div>