<div dir="ltr"><div>Hi Glen - I just tried this with gnuradio HermesNB software and the Rx Xvtr works correctly.<br></div><div>Am using Ver 3.1 of the Hermes FPGA code.<br><br></div>-- Tom, N5EG<br><br></div><div class="gmail_extra"><br><div class="gmail_quote">On Mon, Jun 8, 2015 at 4:42 PM, Glenn Elmore <span dir="ltr"><<a href="mailto:n6gn@sonic.net" target="_blank">n6gn@sonic.net</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">***** High Performance Software Defined Radio Discussion List *****<br>
<br>
This may be entirely apples and oranges but ...<br>
<br>
I have an Angelia board that I use with a TAPR-built Alex/tx board and an Alex/rx board that I've partially loaded - enough to get all the antenna switching features and a couple of HPFs. these are mounted in the Hammond Eurocard extrusion and in a larger chassis which also contains a Pennywhistle 10W PA. It all seems to be working pretty well.<br>
<br>
I'm still learning things about PowerSDRmrx as well as the hardware but thus far, I also have been unable to find any combination of settings that causes the XVRT rx relay to close.  Everything else works and makes sense. On the TX side, A1,A2,A3 all work as expected.  On the RX side, I'm able to either select or bypass the HPF-of-choice while using one of the TX-Ax inputs.  Furthermore, if under Ant/Filters I ask for EXT1 or EXT2, the receiver gets a separate input (though I actually am supplied with the Alex/rx input marked RX2 when I select EXT1 and the one marked RX1 when I select EXT2, it looks like the labeling in PowerSDR columns is swapped). But, under no combination of EXT1,EXT2,XVRT settings  that I can find, even when accompanied by changes in setting under the transverter tab with a transverted band selected or not, can I ever get the Alex/RX BNC input marked XVRT to connect.<br>
<br>
The hardware is bolted together at present so I can't easily examine the drive line but I doubt that it is stuck to the rail. The symptom sounds very similar if not identical to yours.<br>
<br>
I think I've also tried all the above with both 100D and 200D as selected models.<br>
<br>
All the above may be subject to cockpit error.<br>
<br>
Glenn n6gn<br>
<br>
<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Hello,<br>
<br>
I have designed and built an Alex clone with all the Alex features on a<br>
single board to match<br>
the size of the Hermes.<br>
<br>
On my checkout of the board, I noticed that XVTR RX relay is not activating.<br>
Bit 0 of  U3 is high and never<br>
goes low.  All the other relays work.<br>
<br>
Is this a known problem?<br>
<br>
All the HP, LP, antenna relays are functioning.<br>
<br>
???<br>
<br>
73's<br>
<br>
Glen K4KV<br>
<br>
</blockquote>
<br>
_______________________________________________<br>
HPSDR Discussion List<br>
To post msg: <a href="mailto:hpsdr@openhpsdr.org" target="_blank">hpsdr@openhpsdr.org</a><br>
Subscription help: <a href="http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org" target="_blank">http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org</a><br>
HPSDR web page: <a href="http://openhpsdr.org" target="_blank">http://openhpsdr.org</a><br>
Archives: <a href="http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/" target="_blank">http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/</a><br>
</blockquote></div><br></div>