<html>
<body>
<br>
Thanks for the info guys.<br><br>
73, John WoGN<br><br>
At 03:16 PM 7/4/2015, John Laur wrote:<br>
<blockquote type=cite class=cite cite="">Hi, John<br><br>
We have discussed it several times in the past on this and other lists;
the HPSDR protocol is not tolerant of high latency (above about 5ms or
so), packet loss, or out of order packets. Wireless networks inherently
have more of this stuff than local wired networks, and on wide area mesh
networks, such things happen routinely. I would not expect that running
the radio over this type of network would work well if at all.<br><br>
You could use a solution like ghpsdr3-alex provides which is a
client/server architecture that would be more tolerant of this type of
network.Â
<a href="http://napan.ca/ghpsdr3/index.php/Main_Page">
http://napan.ca/ghpsdr3/index.php/Main_Page</a> This would require a
small server computer to be located with the radio.<br><br>
73, John K5IT<br><br>
On Sat, Jul 4, 2015 at 10:22 AM, George Byrkit
<<a href="mailto:ghbyrkit@chartermi.net">ghbyrkit@chartermi.net</a>
> wrote:<br>
<dl>
<dd>***** High Performance Software Defined Radio Discussion List
*****<br><br>
<dd>John,<br>
<dd>Perhaps you are confused and conflating several different projects
(HPSDR and BBhamnet)<br>
<dd>that TAPR has/is supported/supporting, and has featured at the TAPR
forum in Dayton?<br>
<dd>Remember, it's the TAPR forum and not the HPSDR forum!<br><br>
<dd>Hermes can only be used on a local subnet. That is, Hermes
must be on the same subnet as<br>
<dd>the computer controlling it. Just because something is
full-duplex, that doesn't make it<br>
<dd>usable across a routed network like the Internet, WiFi, or something
like BBHamNet. There<br>
<dd>is no routing code in Hermes. There is minimal support for
DHCP, and it's in FPGA logic,<br>
<dd>done carefully by Phil VK6PH.<br><br>
<dd>TAPR has often, in the past, supported such concepts as BBHamNet, and
support has recently<br>
<dd>been increased with the passing of John Stephenson, and the receipt
of a substantial<br>
<dd>bequest in his will to help finish the work that John started.Â
Thus, TAPR has reached out<br>
<dd>to such communities as BBHamNet to try and find support and
developers to finish John's<br>
<dd>work.<br><br>
<dd>So, I do not think that you WOULD use PowerSDR and Hermes over
BBHamNet.<br><br>
<dd>73,<br>
<dd>George Byrkit, K9TRV<br>
<dd>TAPR board member<br><br>
<dd>-----Original Message-----<br>
<dd>From: Hpsdr
[<a href="mailto:hpsdr-bounces@lists.openhpsdr.org" eudora="autourl">
mailto:hpsdr-bounces@lists.openhpsdr.org</a>] On Behalf Of John<br>
<dd>Sent: Saturday, July 04, 2015 10:21 AM<br>
<dd>To:
<a href="mailto:hpsdr@lists.openhpsdr.org">hpsdr@lists.openhpsdr.org</a>
<br>
<dd>Subject: [hpsdr] BBhamnet & Hermes??<br><br>
<dd>***** High Performance Software Defined Radio Discussion List
*****<br><br>
<br>
<dd>I think it was John, AJ6BC, that brought up BBhamnet in the July
4,<br>
<dd>Teamspeak for HPSDR.<br><br>
<dd>Just yesterday I posted a message on the BBhamnet forum asking
how<br>
<dd>one would use BBhamnet to control Hermes:<br><br>
<dd>
<a href="http://www.broadband-hamnet.org/hsmm-mesh-forums/view-postlist/forum-1-general/topic-1630- rig-control-fdx.html">
http://www.broadband-hamnet.org/hsmm-mesh-forums/view-postlist/forum-1-general/topic-1630-<br>
<dd>rig-control-fdx.html</a><br><br>
<dd>Â I do not normally cross post, but it seemed timely to ask
here:<br><br>
<dd>How would I go about using Hermes (with OpenPowerHPSDR) over
BBhamnet?<br><br>
<dd>Since the Hermes Ethernet is full duplex, how can I use it with WiFi
BBhamnet?<br><br>
<dd>John, WoGN<br><br>
<br>
</dl></blockquote></body>
<br>
</html>