<div dir="ltr"><div dir="ltr"><div dir="ltr"><div dir="ltr">Warren,<div><br></div><div>Thanks for your reaction.</div><div><br></div><div>I have tried all the radio models; no change in the sending packet rate.</div><div><br></div><div>I did make the radioberry full duplex (synchronizing all the streams which we have discussed some time ago; which makes thetis working for 48K/96K sampel rate and 1 rx ok) , making the puresignal possible, i like the experiment!</div><div><br></div><div>In powersdr i can activate puresignal by unchecking the disable puresignal....  getting 4 receivers; i do uses rx0 with the ADC samples and provide rx4 with the DAC tx samples value.</div><div>Using P-1 this is possible to do this using 192K sample rate. I still have to some work to test pure signal using powersdr.</div><div><br></div><div>For P-2 i am not able to make 2 slices possible with 192K because of the high data rate from Thetis.</div><div><br></div><div>Iam reading in the protocol port 1025 (DDC SPECIFIC PACKET)</div><div>byte 7 DDC Enable DDC0….DDC7[0] = DDC0, [1]= DDC1……[7] = DDC7</div><div><br></div><div>I do find only 1 DDC.  (may be i need to read to DDC79; i have not done this yet)</div><div><br></div><div><br></div><div>The radioberry firmware contains of a c-part and a fpga part.</div><div><br></div><div>The fpga implements 2 DDC and 1 DUC. In the c part iam possible to control the FPGA part and making the ethernet udp packets; very flexible!</div><div><br></div><div>Where do you enable puresignal in Thetis or is this radiomodel dependent?</div><div><br></div><div>So it seems that the data rate is too.</div><div><br></div><div>73 Johan </div><div>PA3GSB</div><div><br></div><div><br></div></div></div></div></div><br><div class="gmail_quote"><div dir="ltr">Op za 20 okt. 2018 om 17:17 schreef Warren Pratt <warren@pratt.one>:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Hi Johan,<br>
<br>
A bug is always a possibility; however, more likely the bandwidth is higher because of what hardware Thetis thinks is out there and what Thetis features are enabled.  Thetis adjust which DDCs are enabled based upon what hardware is present and what features are enabled.<br>
<br>
For example, for the 14-bit Hermes, there are only two DDCs available in firmware.  So, for that radio model, Thetis will never attempt to enable more than two DDCs.  This results in some loss in functionality.<br>
<br>
However, for an ANAN-7000DLE, Thetis will turn on two DDCs if RX1 and RX2 are enabled and will turn on two more (four total) when PureSignal is in use.  This enables reception on both RX1 and RX2 while transmitting with PureSignal.  Similarly, if running Diversity reception through RX1, RX2 can also be used.  This requires three DDCs to be enabled.<br>
<br>
'radioberry' is not a current choice on Thetis and your results will vary depending upon which hardware Thetis thinks you have.<br>
<br>
73,<br>
Warren  NR0V<br>
<br>
<br>
-----Original Message-----<br>
From: Hpsdr [mailto:<a href="mailto:hpsdr-bounces@lists.openhpsdr.org" target="_blank">hpsdr-bounces@lists.openhpsdr.org</a>] On Behalf Of Johan Maas<br>
Sent: Saturday, October 20, 2018 4:40 AM<br>
To: <a href="mailto:hpsdr@openhpsdr.org" target="_blank">hpsdr@openhpsdr.org</a><br>
Subject: [hpsdr] Thetis and network performance!<br>
<br>
***** High Performance Software Defined Radio Discussion List *****<br>
<br>
</blockquote></div>