<div dir="ltr"><div dir="ltr">Dick,<div><br></div><div>The adjustment is highly non-linear. See the following link:</div><div><br></div><div><a href="https://apache-labs.com/community/viewtopic.php?f=17&t=2471&p=3040">https://apache-labs.com/community/viewtopic.php?f=17&t=2471&p=3040</a></div><div><br></div><div>73,</div><div><br></div><div>Scott</div><div><br><br><div class="gmail_quote"><div dir="ltr">On Wed, Nov 28, 2018 at 10:42 PM Dick Bingham <<a href="mailto:dick.bingham@gmail.com">dick.bingham@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><br>
<div dir="ltr"><div dir="ltr"><div style="">Some of this appears to contradict itself. See highlighted below ===></div><div style="">( <font color="#0000ff"><a href="https://apache-labs.com/downloadsfiles/1024_ANAN-7000DLE-User-Guide.pdf" target="_blank">https://apache-labs.com/downloadsfiles/1024_ANAN-7000DLE-User-Guide.pdf</a></font> )</div><div style="">  </div><div style="">Use the following manual calibration procedure to properly set/calibrate your ANAN-</div><div style="">  7000DLE power output into
a dummy load: </div><div style=""><br></div><div style="">1. Connect a suitable Dummy Load to ANT1 BNC port on the back panel of the </div><div style="">    Transceiver. </div><div style="">2. Click on menu selection, Setup, Transmit. </div><div>3. <b><font color="#ff0000">Set “TUNE”, Power % to 100 </font></b></div><div style="">4. Select “FWD Pwr” from the “TX Meter” upper right corner of the console. </div><div style="">5. Enable the Antenna window by clicking on Setup ---> General ---> ANT/FILTERS </div><div style="">    tab to access the
antenna settings. </div><div style="">6. Select the Transmit antenna ANT1 where you connected the Dummy Load. </div><div style="">7. Select the PA settings TAB on the Setup menu window. The PA Settings TAB allows</div><div style="">    you to set [calibrate] the ANAN-7000DLE Power Amplifier gain by band [dB – </div><div style="">    Power
Output per Band] for each of the available Ham Bands. There is an up/down</div><div style="">    gain control for each band, which
regulates the Power Amplifier output for that </div><div style="">    band. As you increase the Gain By Band, power output will
decrease. Conversely, </div><div style="">    decreasing Gain By Band will increase Power Amplifier output.
Maximum power </div><div style="">    output per band can be reached at the lowest value in this menu. </div><div style="">8. Select one of the bands on the PA settings TAB. </div><div>9. Ensure you have the <b><font color="#ff0000">Setup ---> Transmit tab ---> Tune control set to 10</font></b> and a</div><div style="">    Dummy Load connected to
the selected antenna port on the ANT/FILTERS setup</div><div style="">    tab. </div><div style="">10. Press “TUN” [Tune] on the upper left side of the console. </div><div style="">11. Adjust the band gain value for a MAXIMUM TX Meter “FWD PWR” output
reading</div><div style="">     of 10 watts while using your suitable Dummy Load. Do NOT use an
Antenna for</div><div style="">     this calibration adjustment. </div><div style="">12. Press “TUN” button again to stop transmitting.  <br></div><div style="">================================================================</div><div style="">After following this procedure, my output power seems rather low when I slide the "Drive Level" up toward 100-watts. The two operations highlighted in <font color="#ff0000">red </font><font color="#000000">above</font><font color="#ff0000"> </font><font color="#000000">seem wrong to me.</font></div><div style=""><font color="#000000"><br></font></div><div style=""><font color="#000000">Clarifications appreciated !</font></div><div style=""><font color="#000000"><br></font></div><div style=""><font color="#000000" style="">73  Dick/w7wkr<br></font></div></div></div></blockquote></div></div></div></div>