<!DOCTYPE html><html><head><title></title><style type="text/css">
p.MsoNormal,p.MsoNoSpacing{margin:0}</style></head><body><div type="cite" id="qt"><div style="font-family:Arial;">I returned back to setting up the boards and this problem that I had reported a couple of months ago has come back (not just on 20m, but on all bands).<br></div><div style="font-family:Arial;"><div><br></div></div><div style="font-family:Arial;">The moment I switch to CWL or CWU, Ozy's LED3 starts blinking, which indicates that it is transmitting. Penelope's LEDs also start dancing. I checked the DB9 ports CW inputs for shorts and traced signals till the FPGA inputs for shorts, they all look okay. I also tried connecting both dit and dash inputs of DB9 to the common (ground) on the Ozy DB9 connector and still hear the series of dits. If I connect pin 8 (PTT) of the DB9 to Common (pin 5 of DB9), I hear a series of dot and dashes and it becomes a tone if I untick the iambic mode. Without this input connection, there is no effect on unticking iambic mode, I always hear a series of dots.<br></div><div style="font-family:Arial;"><div><br></div></div><div style="font-family:Arial;">In short, even without any CW key input, the moment powersdr is put into CWL/CWU, the radio starts transmitting on whatever frequency it is on (if it is a valid band) with a constant stream of dits. If I adjust the keyer speed, I can see that the transmitting CW speed also changes.<br></div><div style="font-family:Arial;"><div><br></div></div><div style="font-family:Arial;">I thought Ozy's key inputs are the culprit for a long time, but have reached dead end. Power supply also seem fine, I don't see any variations. I have tried it with and without the PennyWhistle and problem persists (just to rule out that PA is oscillating..). Ozy LED3 clearly indicates that it is transmitting. Is anyone using Ozy with Mercury and Penny facing similar problems with CW mode?<br></div><div style="font-family:Arial;"><div><br></div></div><div style="font-family:Arial;">I spent the whole of today cleaning the boards, looking at the soldering via a magnifying glass and reading the FPGA code. Any clues and debug tips to move forward is highly appreciated!<br></div><div style="font-family:Arial;"><div><br></div></div><div style="font-family:Arial;">73<br></div><div style="font-family:Arial;">Ram VU3RDD<br></div><div style="font-family:Arial;"><div><br></div></div><div>On Wed, Dec 11, 2019, at 12:30 PM, Ramakrishnan Muthukrishnan wrote:<br></div><blockquote type="cite" id="qt-qt"><div>***** High Performance Software Defined Radio Discussion List *****<br></div><div><div><br></div></div><div><div><br></div></div><div style="font-family:Arial;">Thanks Henry. I am not yet using LPU, but am planning to use one soon. I will keep your note in mind.<br></div><div style="font-family:Arial;"><div><br></div></div><div style="font-family:Arial;">It seem like the tone was because the dit input was somehow getting connected to ground. I used IPA and cleaned the Ozy thoroughly and the problem seem to have gone away. Planning to do more testing. I also need to find a housing for the boards so that the dust does not accumulate.<br></div><div style="font-family:Arial;"><div><br></div></div><div style="font-family:Arial;">73<br></div><div style="font-family:Arial;">Ramakrishnan VU3RDD<br></div><div style="font-family:Arial;"><div><br></div></div><div>On Wed, Dec 11, 2019, at 1:07 AM, Henry wrote:<br></div><blockquote id="qt-qt-qt" type="cite"><div>***** High Performance Software Defined Radio Discussion List *****<br></div><div><div><br></div></div><div><div><br></div></div><p>Hi Ramakrishnan,<br></p><p>I'm not sure if you use the "LPU" board or not, but I remember
there was an issue with the electronic fuses on the LPU-board
being too light and they had to be bypassed.<br></p><p>I can also imagine another power supply could be
current-limiting / oscillating?<br></p><p>Anyway, it would be good to check first if the supply voltages
are OK (when this happens).<br></p><p>Good luck,<br></p><p>73,<br></p><p><i>Henry - PA0HJA</i><br></p><p><br></p><div><br></div><p><br></p><div class="qt-qt-qt-moz-cite-prefix">On 9-12-2019 13:48, Ramakrishnan
Muthukrishnan wrote:<br></div><blockquote type="cite" cite="mid:11be0eac-40a0-48d5-b1cc-dd2d3fb70cde@www.fastmail.com"><pre class="qt-qt-qt-moz-quote-pre" wrap="">***** High Performance Software Defined Radio Discussion List *****
Hello:
I have a good old Atlas based system with Penelope, Mercury and Ozy connected to the boards. At this point, I am just listening with Mercury as I do not yet have my pennylane setup and don't have alex boards. So, the antenna is connected to the RF in of mercury. I can listen to stations just fine (with PowerSDR mRX PS, latest available release from the Github) on SSB on every band.
Now, if I switch the band to 20m and push the CWL or CWR button, I get a constant tone - like a series of dits (as if I keep the dit paddle on). If I tune around the frequency, the tone follows there too. I do not have anything connected to the DB25 port of the Ozy. I see the LEDs on Penny (at least the leds 2, 3 and 4) dancing while this is happening, so it looks like it is transmitting when I just switched the receiver to 20m CW. Pushing CWL/CWR on 40m or 80m seem fine and I don't hear the tones.
Has anyone seen this? Or it is that I have setup my systems wrong? I am returning to HPSDR after a very long time, so I may have missed something.. I have latest firmware versions of Mercury and Penelope. I also have PTT explicitly disabled in the "Options" tab under the HPSDR setup. What are the other ways to disable Penny (other than physically pulling it out of the Atlas board)? I am somewhat puzzled why Penny is trying to transmit when I am not transmitting at all. (I don't have a dummy load connected to the output too, so I was a bit alarmed).
Would appreciate advice.
<br></pre></blockquote></blockquote></blockquote></div><div style="font-family:Arial;"><br></div></body></html>