<div dir="ltr"><div>Hi Pete, Helmut, All,</div><div><br></div><div>I tried to flash my Penelope(TAPR) by HPSDRProgrammer_V2_nopcap 2.0. This software identifies Metis board with success. <br></div><div>The question is whether I can flash Penelope through Metis. The Programmer is complaining the rbf file name is incorrect. I put the name " Penelope_v1.8.rbf"  I've just downloaded. <br></div><div>Several years ago,  when I used to use Penelope, I updated the firmware by using Altera Development Software. But the installation required a lot of time. So I would like to use a more elegant way.<br></div><div><br></div><div>73,</div><div>Tokio<br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">2021年10月17日(日) 10:26 Tokio <<a href="mailto:endotokio@gmail.com">endotokio@gmail.com</a>>:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr"><div>Hi Helmut,</div><div><br></div><div>Thank you for your email.</div><div>Pennylane is uncontrollable in terms of Drive. Regardless of Drive Level, the output of Pennylane is around 30dBm. I measured the power at the output of penny, no post-amp for this measurement.<br></div><div>I would like to change the firmware of Penny.</div><div><br></div><div>73,</div><div>Tokio</div><div>JA1CCA<br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">2021年10月17日(日) 0:58 Helmut Oeller <<a href="mailto:dc6ny@gmx.de" target="_blank">dc6ny@gmx.de</a>>:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">***** High Performance Software Defined Radio Discussion List *****<br>
<br>
Hi Tokio,<br>
<br>
if I recall correctly 'drive control' is done by  varying  the DAC<br>
current. Hence I would suggest to check first the real Penny RF output<br>
power without any post-amplifier:<br>
<br>
PA settings 38 dB, drive power 100 percent, apply 'Tune button' and<br>
don't forget to select 'use drive power' in 'transmit/tune' window.<br>
<br>
Output power should be around 500 mW @ 2 - 21 MHz, then power drops to<br>
200 - 400 mW. The TX meter in PowerSDR shows slightly different values.<br>
If all is ok, you can test the 'drive power' variation and measure how<br>
far output followes the 'drive control'.<br>
<br>
73, Helmut, DC6NY<br>
_______________________________________________<br>
HPSDR Discussion List<br>
To post msg: <a href="mailto:hpsdr@openhpsdr.org" target="_blank">hpsdr@openhpsdr.org</a><br>
Subscription help: <a href="http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org" rel="noreferrer" target="_blank">http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org</a><br>
HPSDR web page: <a href="http://openhpsdr.org" rel="noreferrer" target="_blank">http://openhpsdr.org</a><br>
Archives: <a href="http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/" rel="noreferrer" target="_blank">http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/</a></blockquote></div>
</blockquote></div>