[hpsdr] No Microphone audio with Penelope

[Ken N9VV]

And don't forget the hidden initozy.bat microphone pre-amp
on/off switch (hihihi)
----------- initozy11.bat ------------
loadFW 0xfffe 0x0007 ozyfw-sdr1k.hex
msecsleep 3000
loadFPGA 0xfffe 0x0007 Ozy_Janus.rbf
rem        1E 00 - Reset chip
rem        12 01 - set digital interface active
rem        08 15 - D/A on, mic input, mic 20dB boost <-----
rem        08 14 - ditto but no mic boost <----------------
rem        0C 00 - All chip power on
rem        0E 02 - Slave, 16 bit, I2S
rem        10 00 - 48k, Normal mode
rem        0A 00 - turn D/A mute off
writeI2C 0xfffe 0x7 0x1a  0x2  0x1e 0x00
writeI2C 0xfffe 0x7 0x1a  0x2  0x12 0x01
writeI2C 0xfffe 0x7 0x1a  0x2  0x08 0x15
writeI2C 0xfffe 0x7 0x1a  0x2  0x0c 0x00
writeI2C 0xfffe 0x7 0x1a  0x2  0x0e 0x02
writeI2C 0xfffe 0x7 0x1a  0x2  0x10 0x00
writeI2C 0xfffe 0x7 0x1a  0x2  0x0a 0x00
rem
rem the following are for penny
writeI2C 0xfffe 0x7 0x1b  0x2  0x1e 0x00
writeI2C 0xfffe 0x7 0x1b  0x2  0x12 0x01
writeI2C 0xfffe 0x7 0x1b  0x2  0x08 0x15
writeI2C 0xfffe 0x7 0x1b  0x2  0x0c 0x00
writeI2C 0xfffe 0x7 0x1b  0x2  0x0e 0x02
writeI2C 0xfffe 0x7 0x1b  0x2  0x10 0x00
writeI2C 0xfffe 0x7 0x1b  0x2  0x0a 0x00
rem pause


On 9/11/2010 7:45 PM, Ed Thierbach wrote:
> ***** High Performance Software Defined Radio Discussion List *****
>
>
>
>
> Hi, Ron -- the jumpers in question are on your Magister board, not Penelope.
> 73,
> -Ed- AB8OJ
>
> On 9/11/2010 6:31 PM, Ron wrote:
>>    Hello All,
>>
>> I'm sure I am missing something.  I purchased a Penelope from Gerd that
>> doesn't have the silkscreen on the board. Using the gerber files, I
>> identified JP10 and JP11 as what I think are the SDA and SCL jumpers
>> that Bill, KD5TFD referenced in an email response to somebody else with
>> the same problem (also included in the Wiki
>> <http://openhpsdr.org/wiki/index.php?title=Penelope_-_Trouble_Shooting#Microphone_does_not_work_.28Penelope_.2B_Magister.29>).
>> I have the those jumpers installed but still have no audio.  Using the
>> Tune button on PowerSDR 1.16.3.1 shows the transmitter working fine.  I
>> just don't get any audio from the Microphone.
>>
>> The microphone configuration jumpers (PTT, +V, AUD) are set correctly
>> according to the manual and I am running firmware 1.2 in the Penelope.
>>
>> Any idea's what I am missing?  Any hint's would be greatly appreciated.
>>
>> 73's de Ron / WY3D
>> (formerly KI5OH)
>>
>
>
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/

-- 
this email does not contain any 45JBY6 19 pin duo nuvar expanded 
compactron hybrid tubes

 1284252847.0