[hpsdr] No Microphone audio with Penelope

[Ron Mozer]

  Thanks Ed & Ken,

Must be a reading comprehension / memory problem on my end.

I appreciate the info, I think that will take care of me for awhile!

73 de Ron

On 9/11/2010 8:54 PM, Ken N9VV wrote:
> ***** High Performance Software Defined Radio Discussion List *****
>
> And don't forget the hidden initozy.bat microphone pre-amp
> on/off switch (hihihi)
> ----------- initozy11.bat ------------
> loadFW 0xfffe 0x0007 ozyfw-sdr1k.hex
> msecsleep 3000
> loadFPGA 0xfffe 0x0007 Ozy_Janus.rbf
> rem        1E 00 - Reset chip
> rem        12 01 - set digital interface active
> rem        08 15 - D/A on, mic input, mic 20dB boost <-----
> rem        08 14 - ditto but no mic boost <----------------
> rem        0C 00 - All chip power on
> rem        0E 02 - Slave, 16 bit, I2S
> rem        10 00 - 48k, Normal mode
> rem        0A 00 - turn D/A mute off
> writeI2C 0xfffe 0x7 0x1a  0x2  0x1e 0x00
> writeI2C 0xfffe 0x7 0x1a  0x2  0x12 0x01
> writeI2C 0xfffe 0x7 0x1a  0x2  0x08 0x15
> writeI2C 0xfffe 0x7 0x1a  0x2  0x0c 0x00
> writeI2C 0xfffe 0x7 0x1a  0x2  0x0e 0x02
> writeI2C 0xfffe 0x7 0x1a  0x2  0x10 0x00
> writeI2C 0xfffe 0x7 0x1a  0x2  0x0a 0x00
> rem
> rem the following are for penny
> writeI2C 0xfffe 0x7 0x1b  0x2  0x1e 0x00
> writeI2C 0xfffe 0x7 0x1b  0x2  0x12 0x01
> writeI2C 0xfffe 0x7 0x1b  0x2  0x08 0x15
> writeI2C 0xfffe 0x7 0x1b  0x2  0x0c 0x00
> writeI2C 0xfffe 0x7 0x1b  0x2  0x0e 0x02
> writeI2C 0xfffe 0x7 0x1b  0x2  0x10 0x00
> writeI2C 0xfffe 0x7 0x1b  0x2  0x0a 0x00
> rem pause
>
>
> On 9/11/2010 7:45 PM, Ed Thierbach wrote:
>> ***** High Performance Software Defined Radio Discussion List *****
>>
>>
>>
>>
>> Hi, Ron -- the jumpers in question are on your Magister board, not 
>> Penelope.
>> 73,
>> -Ed- AB8OJ
>>
>> On 9/11/2010 6:31 PM, Ron wrote:
>>>    Hello All,
>>>
>>> I'm sure I am missing something.  I purchased a Penelope from Gerd that
>>> doesn't have the silkscreen on the board. Using the gerber files, I
>>> identified JP10 and JP11 as what I think are the SDA and SCL jumpers
>>> that Bill, KD5TFD referenced in an email response to somebody else with
>>> the same problem (also included in the Wiki
>>> <http://openhpsdr.org/wiki/index.php?title=Penelope_-_Trouble_Shooting#Microphone_does_not_work_.28Penelope_.2B_Magister.29>). 
>>>
>>> I have the those jumpers installed but still have no audio.  Using the
>>> Tune button on PowerSDR 1.16.3.1 shows the transmitter working fine.  I
>>> just don't get any audio from the Microphone.
>>>
>>> The microphone configuration jumpers (PTT, +V, AUD) are set correctly
>>> according to the manual and I am running firmware 1.2 in the Penelope.
>>>
>>> Any idea's what I am missing?  Any hint's would be greatly appreciated.
>>>
>>> 73's de Ron / WY3D
>>> (formerly KI5OH)
>>>
>>
>>
>> _______________________________________________
>> HPSDR Discussion List
>> To post msg: hpsdr at openhpsdr.org
>> Subscription help: 
>> http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
>> HPSDR web page: http://openhpsdr.org
>> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>



 1284254999.0