[hpsdr] Programming Hermes Help

[Phil Harman]

I guess the problem I have with this is that I'm way too close to the
problem to see the solution.

I've re-read the User Guide and can't see how it can be made any clearer.
But, perhaps I read between the lines too well!

If someone who has been through this process can suggest some changes or
additional text then I'd be glad to incorporate it.

I think the ultimate solution would be to incorporate the programming
function into the PC software.  That way the PC could periodically check
for updates being available and ask the user if they want to install it.

73 Phil..VK6APH

> ***** High Performance Software Defined Radio Discussion List *****
>
> That was it, 20 seconds and it was done. 4 hours and all it was J12 being
> installed!!
> Others be warned!!
> Tim
>
>
> -----Original Message-----
>>From: N4IS <n4is at comcast.net>
>>Sent: Dec 2, 2012 5:30 PM
>>To: 'Tim O'Rourke' <w4yn at earthlink.net>, hpsdr at lists.openhpsdr.org
>>Subject: RE: [hpsdr] Programming Hermes Help
>>
>>Hi Tim
>>
>>I experienced the same situation you describe. Several attempts to get
>>Hermes discovered with no joy, but always able to see the Mac address and
>>the IP was 255.255.255.255. After reading the recommendations to upload
>> the
>>firmware I understood it and you don't need to change J12 to upgrade the
>>firmware. J12 is necessary to be on for the boot loader.
>>
>>I removed J12 , power cycled Hermes and started PowerSDR. It worked
>>correctly, just quite a longer time to start.  I closed PowerSDR, then
>>another  power recycle Hermes and open programmer again, this time it
>>recognized Hermes and the firmware upgrade was easy as expected. It seems
>>that if you start with J12 on the board is not able to get an IP address.
>>
>>I have a TAPR Hermes and now the firmware is updated and working just
>> fine.
>>
>>Regards
>>Jose Carlos
>>N4IS
>>
>>-----Original Message-----
>>From: hpsdr-bounces at lists.openhpsdr.org
>>[mailto:hpsdr-bounces at lists.openhpsdr.org] On Behalf Of Tim O'Rourke
>>Sent: Sunday, December 02, 2012 1:43 PM
>>To: hpsdr at lists.openhpsdr.org
>>Subject: [hpsdr] Programming Hermes Help
>>
>>***** High Performance Software Defined Radio Discussion List *****
>>
>>Well I am stuck, I can not discover Hermes.
>>Have connection set to Obtain IP address automatically.
>>I select the direct connection port in Programmer, I see Mac address that
>>looks correct to what I have read.
>>But I can not discover Hermes.
>>I have TAPR Hermes. All else seems fine with programmer.
>>Tim
>>
>>Tim O'Rourke
>>W4YN at ARRL.Net
>>Low Power Amateur Radio Rocks
>>Member of Flying Pigs,ARCI,GQRP,RSGB,ARRL Life Member NHRA Life Member
>>_______________________________________________
>>HPSDR Discussion List
>>To post msg: hpsdr at openhpsdr.org
>>Subscription help:
>>http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
>>HPSDR web page: http://openhpsdr.org
>>Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>>
>
>
> Tim O'Rourke
> W4YN at ARRL.Net
> Low Power Amateur Radio Rocks
> Member of Flying Pigs,ARCI,GQRP,RSGB,ARRL Life Member
> NHRA Life Member
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help:
> http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>
>



 1354497417.0