[hpsdr] mercury deaf [was Hello]

[AD0ES]

Hi,

It was requested that I send the startup commands I am using.  Hopefully
this isn't "tmi".


Using ghpsdr3-alex.

-------------------
Start hpsdr-server:
/usr/local/bin/hpsdr-server --metis --interface eth0 --10mhzsource mercury --122.88mhzsource mercury

hpsdr-server output:
Looking for Metis card on interface eth0
Metis MAC address 00:04:A3:D3:CD:2B
Metis IP address 10.11.12.45
Board id: Metis version:  2.60
Found 1 Metis/Hermes cards
Metis starting receive thread
Listening for TCP connections on port 11000
ozy_prime: configure=6
sent to Metis:(0)
  [0000] 7F7F7F00F9001800 0000000000000000
...
ozy_prime: configure=1
...
ozy_prime: current_receiver=0
...
sent to Metis:(7)
  [0000] 7F7F7F00F9001800 0000000000000000
...
server configured for 1 receivers at 96000
starting metis_watchdog_thread
running metis_watchdog_thread
received from Metis:(0)
...

  Mercury Software version: 255 (0xFF)
  Penelope Software version: 255 (0xFF)
  Ozy Software version: 26 (0x1A)
received from Metis:(2)
...
received from Metis:(9)

----------------
Start dspserver:
/usr/local/bin/dspserver --lo 0 --hpsdr --nocorrectiq

dspserver output:
Reading conf file /home/smp/dspserver.conf
gHPSDR rx 0 (Version 0.7)
dspserver string: 20131230;-master
getSoundcardId: HPSDR id=8
setSoundcard: 8
setSoundcard -41.000000 -48.000000
setup sdr thread 0: done
setup sdr thread 1: done
setup sdr thread 2: done
client_thread
[2014-07-23 09:02:35] client_thread: listening on port 8000
G711A_init
ozy_init: command bound to port 12000 socket 5
ozy_init: audio bound to port 0 socket 6
ozy_init: server audio is in port 15000
ozy_init: server 127.0.0.1
connect: sampleRate=96000
setSpeed 96000
LO_offset 0.000000
[2014-07-23 09:02:35] client_thread: listening on port 9000 for ssl connection
setSpeed: 96000.000000
setSpeed: mic source ratio: 12.000000
ozy_init: sample rate init successfully at ratio: 0.083333
iq_thread
iq_thread: iq bound to port 13000 socket=11
audiostream_conf.samplerate=8000
[2014-07-23 09:02:35] tx_init: sample rate init successful with ratio of : 12.000000
[2014-07-23 09:02:35] tx_thread STARTED

--------------
Start QtRadio:
/src/ghpsdr3-alex/trunk/src/QtRadio/QtRadio
...

-------------------------------
additional hpsdr-server output:
ozy_set_preamp: 1 0x1C
ozy_set_hermes_att: 0x20
ozy_set_alex_tx_relay: 0: 0x00

----------------------------
additional dspserver output:

[2014-07-23 09:11:18] RX0: client connection from 127.0.0.1:56939
[2014-07-23 09:11:18] SetCorrectIQEnable(0)
[2014-07-23 09:11:18] IGNORING (due to --ignore-iq option) the value of mu sent = '0.17'
[2014-07-23 09:11:18] RX0: client is QtRadio
[2014-07-23 09:11:18] SetPWSMode 0
[2014-07-23 09:11:18] encoding changed to 0
[2014-07-23 09:11:18] starting audio stream at rate 8000 channels 1 bufsize 2000 encoding 0 micEncoding 0
[2014-07-23 09:11:18] SetPWSMode 0
[2014-07-23 09:11:18] SetRXDCBlock 0
[2014-07-23 09:11:18] SetTXDCBlock 1
Invalid command: 'setalcstate'
HARDWARE DIRECTED: message: '*hardware?'
response to STAR message: [OK Hermes]
DttSP::SetRXManualNotchEnable(0, 0, 0, 0)
 ...
DttSP::SetRXManualNotchEnable(0, 1, 8, 0)
HARDWARE DIRECTED: message: '*getserial?'
response to STAR message: [OK 10.11.12.45"- firmware 0"]
HARDWARE DIRECTED: message: '*dither on'
response to STAR message: [OK]
HARDWARE DIRECTED: message: '*preamp on'
response to STAR message: [OK]
HARDWARE DIRECTED: message: '*random on'
response to STAR message: [OK]
HARDWARE DIRECTED: message: '*setattenuator 0'
response to STAR message: [OK]
HARDWARE DIRECTED: message: '*alextxrelay 0'
response to STAR message: [OK]
[2014-07-23 09:11:18] Spectrum fps set to = '15'

tia,
Steve  AD0ES