[hpsdr] Angelia_Protocol_2_v11.6/ANAN-100D firmware available for download

[Joe Martin]

Actually, I see that you have to double-click on the filename to get the download button to appear.  This procedure isn’t difficult.  It will simply take some getting used to though as it is a little different from the previous SVN download procedures. 

73, Joe K5SO

> On Apr 23, 2017, at 7:41 PM, Joe Martin <k5so at k5so.com> wrote:
> 
> ***** High Performance Software Defined Radio Discussion List *****
> 
> And for highly detail-oriented folks, I see that the file size for this particular firmaware version happens to be 1.32MB not 1.8MB so don’t get thrown by that nit.  Thanks!
> 
> 73, Joe K5SO
> 
>> On Apr 23, 2017, at 7:36 PM, Joe Martin <k5so at k5so.com> wrote:
>> 
>> ***** High Performance Software Defined Radio Discussion List *****
>> 
>> All, 
>> 
>> There appears to be some confusion.  The download button I refer to below is not the green “Clone or download” button you see on the top level of the OpenHPSDR-Firmware repository.  It is the button that appears after you select the Orion_Protocol_2_v11.6.rbf filename on the 
>> 
>> OpenHPSDR-Firmware > Protocol 2 > Angelia (ANAN-100D)  page. 
>> 
>> If you select the green button on the top level of the OpenHPSDR-Firmware page you will download the entire OpenHPSDR-Firmware repository, which is not what you want to do if you wish to obtain only the 1.8 MB Orion_Protocol_2_v11.6.rbf file.  
>> 
>> 73, Joe K5SO
>> 
>> 
>>> On Apr 23, 2017, at 6:02 PM, Joe Martin <k5so at k5so.com> wrote:
>>> 
>>> ***** High Performance Software Defined Radio Discussion List *****
>>> 
>>> All. 
>>> 
>>> New firmware for Angelia/ANAN-100D Protocol 2 is available for download from 
>>> 
>>> http://github.com/TAPR/OpenHPSDR-Firmware
>>> 
>>> Be sure to use the DOWNLOAD button on the web page to obtain the download; do NOT double-click on the file name nor right-click “Save As” to download the file as doing either of these latter two actions will not download the 1.8MB file.  
>>> 
>>> This firmware must be used with Thetis or other Protocol 2 software; not PowerSDR (which requires Protocol 1).  
>>> 
>>> This version adds peak detection to FWD_PWR (AIN1) and REV_PWR (AIN2) and speeds up user ADC conversion rates x10. It also modifies the PHY Rx clock skew timing to (hopefully) allow use of the firmware on more ANAN-100D radios with less undesirable unit-specific behavior.  The version also fixes the external PTT IN feature (pin 13 on the accessory jack of the ANAN-100D).  
>>> 
>>> 73, Joe K5SO
>>> 
>>> _______________________________________________
>>> HPSDR Discussion List
>>> To post msg: hpsdr at openhpsdr.org
>>> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
>>> HPSDR web page: http://openhpsdr.org
>>> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>> 
>> _______________________________________________
>> HPSDR Discussion List
>> To post msg: hpsdr at openhpsdr.org
>> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
>> HPSDR web page: http://openhpsdr.org
>> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
> 
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/