[hpsdr] THETIS manual updated draft

[Richard Grubb]

Hi Laurence,

FYI. RX2 on Thetis v2.6.9 works when loading the GitHub release.

73, Dick

------ Original Message ------
From: "Richard Grubb" <richard.n.grubb at comcast.net>
To: laurence at nicklebyhouse.co.uk; hpsdr at lists.openhpsdr.org
Sent: 2/24/2020 9:58:24 AM
Subject: Re: [hpsdr] THETIS manual updated draft

>***** High Performance Software Defined Radio Discussion List *****
>
>Hi Laurence,
>
>The version of Thetis I had downloaded from your site announces itself 
>as v2.6.9. That version did not bring up RX2. I removed it and did a 
>clean install of v2.6.8 from the GitHub release directory. RX2 now 
>works.  I should probably try v2.6.9 again using the Git Hub release.
>
>On Hermes with the single ADC, RX2 just provides access to a second 
>DDC. as you expected. I had to consult your manual to understand how 
>the display of RX2 now works. The seemingly forced dual display mode is 
>a change from PowerSDR and the audio selection is an additional 
>complication. I must play with it some more.
>
>73, Dick
>W0QM, G3FNL
>
>------ Original Message ------
>From: "Laurence Barker" <laurence at nicklebyhouse.co.uk>
>To: "'Richard Grubb'" <richard.n.grubb at comcast.net>; 
>hpsdr at lists.openhpsdr.org
>Sent: 2/23/2020 12:24:20 PM
>Subject: RE: [hpsdr] THETIS manual updated draft
>
>>Hi Dick
>>
>>
>>No, that's not a known issue - RX2 works fine on my radio.
>>
>>The version of Thetis on my website is really for beta testing of 
>>Andromeda; you would be better using the published releases! I'd be 
>>surprised if it was different though.
>>
>>I'm not sure how RX2 works on Hermes - I assume it routes the same ADC 
>>to a different downconverter.
>>
>>
>>
>>
>>
>>Laurence Barker
>>
>>laurence at nicklebyhouse.co.uk
>>
>>
>>-----Original Message-----
>>From: Richard Grubb [mailto:richard.n.grubb at comcast.net]
>>Sent: 23 February 2020 17:47
>>To: laurence at nicklebyhouse.co.uk; hpsdr at lists.openhpsdr.org
>>Subject: Re: [hpsdr] THETIS manual updated draft
>>
>>Hi Laurence,
>>
>>Thank you very much for this manual. It looks like an excellent 
>>document.
>>
>>I just updated the firmware on on my Hermes to Protocol 2 v10.8. I 
>>installed the Thetis 9 Feb 2020 software from your web site. 
>>Everything I have tried seems to work except RX2 is not functional. 
>>However that is not too important to me at present. Is this a known 
>>problem ?
>>
>>73, Dick
>>W0QM, G3FNL
>>
>>------ Original Message ------
>>From: "Laurence Barker" <laurence at nicklebyhouse.co.uk>
>>To: hpsdr at lists.openhpsdr.org
>>Sent: 2/23/2020 7:04:46 AM
>>Subject: [hpsdr] THETIS manual updated draft
>>
>>>***** High Performance Software Defined Radio Discussion List *****
>>>
>>>Thank you to everyone who contributed to the THETIS manual recently.
>>>I've put an updated version on my website here:
>>>
>>>http://www.nicklebyhouse.co.uk/index.php/downloads/category/13-sdr?down
>>>load=55:thetis-manual-draft-0-4
>>>
>>>
>>>Laurence Barker G8NJJ
>>>
>>>laurence at nicklebyhouse.co.uk
>>>
>>>_______________________________________________
>>>HPSDR Discussion List
>>>To post msg: hpsdr at openhpsdr.org
>>>Subscription help:
>>>http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
>>>HPSDR web page: http://openhpsdr.org
>>>Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>>
>
>_______________________________________________
>HPSDR Discussion List
>To post msg: hpsdr at openhpsdr.org
>Subscription help: 
>http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
>HPSDR web page: http://openhpsdr.org
>Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/