[hpsdr] Thetis v2.8.11 with Hermes.

[Chris Gerber]

Thanks Martin for the program.
My first impression is great. It fixed one problem which I searched for 
weeks, but shall come back
to the matter in general. There are still the former from me mention 
problems present, like Power Meter
or that Vac is not invoked on start. But as whole its working as best TX 
program I have in use here, and there
many.

Thanks again
Chris HB9BDM





Am 10.11.2020 um 08:57 schrieb Martin Emmerson:
> ***** High Performance Software Defined Radio Discussion List *****
>
>
> Thanks both and it seems it is not just me, so I hope this will be 
> fixed in the next release...
> Now we can see the big advantage in open source code, at least anyone 
> can have a go at
> fixing any bugs - I would not use anything else.
> If anyone is in a hurry for a fixed version I can send them my fixed 
> executable - 11,5MB.
>
> 73's
>
> Martin G3OQD.
>
> On Sun, 8 Nov 2020 at 14:31, Kjell Karlsen <la2ni at online.no 
> <mailto:la2ni at online.no>> wrote:
>
>     ***** High Performance Software Defined Radio Discussion List *****
>
>     Hi Martin.
>
>     I discovered the  high power indicated  problem earlier today and
>     was going to mention it! So now I hope it is solved soon.
>
>     73, Kjell
>
>     Den 08.11.2020 15:15, skrev Helmut Oeller:
>>     ***** High Performance Software Defined Radio Discussion List *****
>>
>>
>>     Hallo Martin,
>>
>>     no new finding, but not less annoying and/or confusing. I think
>>     the bug will be deleted soon. BTW, this time I used Thetis only
>>     under protocol 1. No knowledge if this issue also exists under
>>     protocol 2 mode.
>>
>>     Take it easy as Hermes will NEVER deliver 35 or 40 watts, hi.
>>
>>     73, Helmut, DC6NY
>>
>>
>>
>>     Am 08.11.2020 um 13:42 schrieb Martin Emmerson:
>>>     ***** High Performance Software Defined Radio Discussion List *****
>>>
>>>
>>>     Has anyone, using this combination, noticed that on TX the
>>>     Thetis Fwd Pwr shows about 35W?
>>>     This is with the General -> H/W Select -> Hardware - Alex box
>>>     unticked so this should not
>>>     happen.
>>>     Also get over SWR warnings which can be stopped by unticking SWR
>>>     protection in the Alex
>>>     tab but Alex should not be active with its box unticked?
>>>     After some investigation I found the following line of code in
>>>     setup.cs:
>>>     //    console.AlexPresent = chkAlexPresent.Checked;
>>>     Removing the "//" from the start of the line and recompiling the
>>>     code has resolved the problem!
>>>     I cannot see any reason this line has been commented out? as the
>>>     checkbox is there to
>>>     enable/disable Alex.
>>>     I realise that most people won't notice this, especially those
>>>     that have Alex or equivalent.
>>>     However a friend G3KOM who is going to use his Hermes to drive a
>>>     2m transverter was rather
>>>     concerned about this erroneous power output reading...
>>>
>>>     I wonder if anyone can tell me why the Alex tickbox has been
>>>     rendered inactive?
>>>
>>>     Thanks
>>>
>>>     Martin G3OQD.
>>>
>>>     _______________________________________________
>>>     HPSDR Discussion List
>>>     To post msg:hpsdr at openhpsdr.org  <mailto:hpsdr at openhpsdr.org>
>>>     Subscription help:http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
>>>     HPSDR web page:http://openhpsdr.org
>>>     Archives:http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>>
>>     _______________________________________________
>>     HPSDR Discussion List
>>     To post msg:hpsdr at openhpsdr.org  <mailto:hpsdr at openhpsdr.org>
>>     Subscription help:http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
>>     HPSDR web page:http://openhpsdr.org
>>     Archives:http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>     _______________________________________________
>     HPSDR Discussion List
>     To post msg: hpsdr at openhpsdr.org <mailto:hpsdr at openhpsdr.org>
>     Subscription help:
>     http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
>     HPSDR web page: http://openhpsdr.org
>     Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>
>
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/attachments/20201111/81706274/attachment.html>