[hpsdr] Thetis v2.8.11 with Hermes.

[Martin Emmerson]

Thanks both and it seems it is not just me, so I hope this will be fixed in
the next release...
Now we can see the big advantage in open source code, at least anyone can
have a go at
fixing any bugs - I would not use anything else.
If anyone is in a hurry for a fixed version I can send them my fixed
executable - 11,5MB.

73's

Martin G3OQD.

On Sun, 8 Nov 2020 at 14:31, Kjell Karlsen <la2ni at online.no> wrote:

> ***** High Performance Software Defined Radio Discussion List *****
>
> Hi Martin.
>
> I discovered the  high power indicated  problem earlier today and was
> going to mention it! So now I hope it is solved soon.
>
> 73, Kjell
> Den 08.11.2020 15:15, skrev Helmut Oeller:
>
> ***** High Performance Software Defined Radio Discussion List *****
>
>
>
> Hallo Martin,
>
> no new finding, but not less annoying and/or confusing. I think the bug
> will be deleted soon. BTW, this time I used Thetis only under protocol 1.
> No knowledge if this issue also exists under protocol 2 mode.
>
> Take it easy as Hermes will NEVER deliver 35 or 40 watts, hi.
>
> 73, Helmut, DC6NY
>
>
>
> Am 08.11.2020 um 13:42 schrieb Martin Emmerson:
>
> ***** High Performance Software Defined Radio Discussion List *****
>
>
>
> Has anyone, using this combination, noticed that on TX the Thetis Fwd Pwr
> shows about 35W?
> This is with the General -> H/W Select -> Hardware - Alex box unticked so
> this should not
> happen.
> Also get over SWR warnings which can be stopped by unticking SWR
> protection in the Alex
> tab but Alex should not be active with its box unticked?
> After some investigation I found the following line of code in setup.cs:
> //    console.AlexPresent = chkAlexPresent.Checked;
> Removing the "//" from the start of the line and recompiling the code has
> resolved the problem!
> I cannot see any reason this line has been commented out? as the checkbox
> is there to
> enable/disable Alex.
> I realise that most people won't notice this, especially those that have
> Alex or equivalent.
> However a friend G3KOM who is going to use his Hermes to drive a 2m
> transverter was rather
> concerned about this erroneous power output reading...
>
> I wonder if anyone can tell me why the Alex tickbox has been rendered
> inactive?
>
> Thanks
>
> Martin G3OQD.
>
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>
>
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help:
> http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/attachments/20201110/5a6da717/attachment.html>