[hpsdr] Heil HC-5 and Logitech skype head set drive problem

[K1rqg at aol.com]

Lou
 
You can edit initozy11.bat as follows:
 
******
 
loadFW 0xfffe 0x0007 ozyfw-sdr1k.hex
msecsleep 3000
loadFPGA 0xfffe  0x0007 Ozy_Janus.rbf
rem        1E 00 -  Reset chip
rem        12 01 - set digital  interface active
rem        08 15 - D/A  on, mic input, mic 20dB boost
rem         08 14 - ditto but no mic boost
rem         0C 00 - All chip power on
rem        0E 02  - Slave, 16 bit, I2S
rem        10 00 -  48k, Normal mode
rem        0A 00 - turn  D/A mute off
writeI2C 0xfffe 0x7 0x1a  0x2  0x1e 0x00
writeI2C  0xfffe 0x7 0x1a  0x2  0x12 0x01
writeI2C 0xfffe 0x7 0x1a   0x2  0x08 0x15  edit 0x15 to 0x14 (for Janus)
writeI2C 0xfffe 0x7  0x1a  0x2  0x0c 0x00
writeI2C 0xfffe 0x7 0x1a  0x2  0x0e  0x02
writeI2C 0xfffe 0x7 0x1a  0x2  0x10 0x00
writeI2C 0xfffe  0x7 0x1a  0x2  0x0a 0x00
rem
rem the following are for  penny
writeI2C 0xfffe 0x7 0x1b  0x2  0x1e 0x00
writeI2C 0xfffe  0x7 0x1b  0x2  0x12 0x01
writeI2C 0xfffe 0x7 0x1b  0x2   0x08 0x15 edit 0x15 to 0x14 (for Penny)
writeI2C 0xfffe 0x7 0x1b   0x2  0x0c 0x00
writeI2C 0xfffe 0x7 0x1b  0x2  0x0e  0x02
writeI2C 0xfffe 0x7 0x1b  0x2  0x10 0x00
writeI2C 0xfffe  0x7 0x1b  0x2  0x0a 0x00
rem pause
 
See the "rem" statements at beginning of file.
 
******
 
Make sure you set jumpers correctly on Penny for a condenser mike for  the
Logitech headset. If you need more gain, you can check "Mic Boost" on
in Setup on Primary audio tab. Don't forget to either manually run  
initozy11.bat
or shut power off to penny for the edit changes to take place.
 
73 de Joe
K1RQG
 
 
In a message dated 6/26/2010 1:25:32 A.M. Eastern Daylight Time,  
n1giz at yahoo.com writes:

*****  High Performance Software Defined Radio Discussion List *****

First the  Heil hc-5 over drives power sdr (vox set to max)
and second the Logitech  skype head set under
drives (not enough drive for Penelope) power  sdr.

Any help would be greatly appreciated.


Thanks
Lou  n1giz



-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/attachments/20100626/418a2f4d/attachment-0003.htm>