[hpsdr] Angelia_v2.8 firmware download

[Joe Martin K5SO]

Okay, thanks.  I am scheduled to receive an actual ANAN-100D here today so I will be able to test the behavior of Tx and filter switching here shortly, too.  There is no reason that I can think of to explain your observations (please check that Angelia_v2.8 is actually showing up as the firmware version in your PowerSDR menu when you think v2.8 is in your unit).  

73,  Joe K5SO


On Feb 8, 2014, at 9:12 AM, Steven Doyle wrote:

> I too can confirm that the power out on 10m has dropped in v2.8.  Restoring v2.7 and the power out on 10m is also fixed.
> 
> -----Original Message----- From: mstangelo at comcast.net
> Sent: Saturday, February 08, 2014 3:51 PM
> To: Joe Martin K5SO ; apache-labs at yahoogroups.com
> Cc: hpsdr at lists.openhpsdr.org
> Subject: Re: [hpsdr] Angelia_v2.8 firmware download
> 
> ***** High Performance Software Defined Radio Discussion List *****
> 
> Joe,
> 
> I upgraded form v2.7 to v2.8 using HPDSRProgrammerV2 nopcap 2.0.4.5 2013-12-1 ans in programmed successfully. The erase cycle took about a minute. The programming cycle took less that 5 seconds.
> 
> I checked the power and the maximum 10 meter power dropped to 70 watts.
> 
> I downgraded from v2.8 to 2.7 with the HPDSRProgrammerV2. The erase cycle took about a minute. It then stataed "1 board found". There was not any programming message. I ran a discover and it showed Angelia v2.7.
> 
> I checked the power and the maximum 10 meter increased to 100 watts.
> 
> Why didn't the programming ststus display when downgrading from v2.8 to v2.7?
> 
> Why is the maximum 10 meter power lower on 2.8. I also had this issue with v2.6?
> 
> Mike N2MS
> 
> ----- Original Message -----
> From: Joe Martin K5SO <k5so at valornet.com>
> To: dl8laq at sh-home.de
> Cc: hpsdr at lists.openhpsdr.org list <hpsdr at lists.openhpsdr.org>
> Sent: Sat, 08 Feb 2014 14:53:34 -0000 (UTC)
> Subject: Re: [hpsdr] Angelia_v2.8 firmware download
> 
> ***** High Performance Software Defined Radio Discussion List *****
> 
> Norbert and Les,
> 
> I am not able to reproduce your failures here; I’ve been able to switch back and forth between Angelia_v2.7 and Angelia_v2.8 repeatedly without any problems.
> 
> Keep in mind that if Angelia_v2.7 is in your ANAN-100D it will take HPSDR Programmer about 68 seconds or so to erase the EEPROM, whereas if Angelia_v2.8 is in your ANAN-100D the erase time is only about 17 seconds.
> 
> I’m not sure what to think about your results; we’ll see if they are generally observed, I’ve only heard of these two instances of failure among several several successful reports from users so far.
> 
> 73,  Joe K5SO
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/ 


 1391876304.0