[hpsdr] Angelia_Protocol_2_v11.6/ANAN-100D firmware available for download

[Joe Martin]

Bob, 

The usual HPSDR Programmer does not work with Protocol 2.  

If you have Protocol 1 firmware in your radio you may (one time) load either Protocol 1 or Protocol 2 firmware using the current HPSDR programmer but after Protocol 2 is in the radio the current HPSDR programmer will no longer work;  you must thereafter use bootloader mode to change firmware once Protocol 2 firmware is in the radio. 

Dave KV0S has a beta version of Protocol 2 programmer that sometimes works on Windows machines and sometimes not; there are still problems with it.  I think it may be on the github repository if you wish to give it a try.  But, in any case, any version of bootloader will work to load any firmware regardless of whether Protocol 1 or Protocol 2 is in the radio.  

73, Joe K5SO

> On Apr 24, 2017, at 3:02 PM, Robert Lorenzini <bob at llorenzini.com> wrote:
> 
> ***** High Performance Software Defined Radio Discussion List *****
> 
> After programming the radio I lost discovery but P2 was up and running.
> I found a conflict between VAC1 and VAC2. If both were enabled I had
> no tx on VAC1. It looked like there were no dropouts on the Pi using WiFi
> with P2. It has been years since I used the bootloader, I guess I will have
> to find my jumper extender.
> 
> Bob - wd6dod
> 
> On 4/23/2017 7:00 PM, Joe Martin wrote:
>> ***** High Performance Software Defined Radio Discussion List *****
>> 
>> Actually, I see that you have to double-click on the filename to get the download button to appear.  This procedure isn’t difficult.  It will simply take some getting used to though as it is a little different from the previous SVN download procedures.
>> 
>> 73, Joe K5SO
>> 
>>> On Apr 23, 2017, at 7:41 PM, Joe Martin <k5so at k5so.com> wrote:
>>> 
>>> ***** High Performance Software Defined Radio Discussion List *****
>>> 
>>> And for highly detail-oriented folks, I see that the file size for this particular firmaware version happens to be 1.32MB not 1.8MB so don’t get thrown by that nit.  Thanks!
>>> 
>>> 73, Joe K5SO
>>> 
>>>> On Apr 23, 2017, at 7:36 PM, Joe Martin <k5so at k5so.com> wrote:
>>>> 
>>>> ***** High Performance Software Defined Radio Discussion List *****
>>>> 
>>>> All,
>>>> 
>>>> There appears to be some confusion.  The download button I refer to below is not the green “Clone or download” button you see on the top level of the OpenHPSDR-Firmware repository.  It is the button that appears after you select the Orion_Protocol_2_v11.6.rbf filename on the
>>>> 
>>>> OpenHPSDR-Firmware > Protocol 2 > Angelia (ANAN-100D)  page.
>>>> 
>>>> If you select the green button on the top level of the OpenHPSDR-Firmware page you will download the entire OpenHPSDR-Firmware repository, which is not what you want to do if you wish to obtain only the 1.8 MB Orion_Protocol_2_v11.6.rbf file.
>>>> 
>>>> 73, Joe K5SO
>>>> 
>>>> 
>>>>> On Apr 23, 2017, at 6:02 PM, Joe Martin <k5so at k5so.com> wrote:
>>>>> 
>>>>> ***** High Performance Software Defined Radio Discussion List *****
>>>>> 
>>>>> All.
>>>>> 
>>>>> New firmware for Angelia/ANAN-100D Protocol 2 is available for download from
>>>>> 
>>>>> http://github.com/TAPR/OpenHPSDR-Firmware
>>>>> 
>>>>> Be sure to use the DOWNLOAD button on the web page to obtain the download; do NOT double-click on the file name nor right-click “Save As” to download the file as doing either of these latter two actions will not download the 1.8MB file.
>>>>> 
>>>>> This firmware must be used with Thetis or other Protocol 2 software; not PowerSDR (which requires Protocol 1).
>>>>> 
>>>>> This version adds peak detection to FWD_PWR (AIN1) and REV_PWR (AIN2) and speeds up user ADC conversion rates x10. It also modifies the PHY Rx clock skew timing to (hopefully) allow use of the firmware on more ANAN-100D radios with less undesirable unit-specific behavior.  The version also fixes the external PTT IN feature (pin 13 on the accessory jack of the ANAN-100D).
>>>>> 
>>>>> 73, Joe K5SO
>>>>> 
>>>>> _______________________________________________
>>>>> HPSDR Discussion List
>>>>> To post msg: hpsdr at openhpsdr.org
>>>>> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
>>>>> HPSDR web page: http://openhpsdr.org
>>>>> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>>>> _______________________________________________
>>>> HPSDR Discussion List
>>>> To post msg: hpsdr at openhpsdr.org
>>>> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
>>>> HPSDR web page: http://openhpsdr.org
>>>> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>>> _______________________________________________
>>> HPSDR Discussion List
>>> To post msg: hpsdr at openhpsdr.org
>>> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
>>> HPSDR web page: http://openhpsdr.org
>>> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>> _______________________________________________
>> HPSDR Discussion List
>> To post msg: hpsdr at openhpsdr.org
>> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
>> HPSDR web page: http://openhpsdr.org
>> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
> 
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help: http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/