[hpsdr] Angelia_v2.0 firmware and new output_file.pof file

[William H. Fite]

And a switch to change between internal and external frequency reference.
And maybe one to control phantom mic power.  All useful, I think.


On Tue, Sep 17, 2013 at 11:54 AM, Joe Martin K5SO <k5so at valornet.com> wrote:

> ***** High Performance Software Defined Radio Discussion List *****
>
> Even better!
>
> 73,  Joe K5SO
>
> On Sep 17, 2013, at 9:28 AM, Clyde Washburn wrote:
>
> > There is room just to the right of the Ethernet jack on the anan-100d
> front panel to install a small toggle switch to jumper j17
> > without opening the unit -- that was my solution.
> >
> > Clyde, K2UE
> >
> > -----Original Message-----
> > From: hpsdr-bounces at lists.openhpsdr.org [mailto:
> hpsdr-bounces at lists.openhpsdr.org] On Behalf Of Joe Martin K5SO
> > Sent: Tuesday, September 17, 2013 7:59 AM
> > To: mstangelo at comcast.net
> > Cc: hpsdr list
> > Subject: Re: [hpsdr] Angelia_v2.0 firmware and new output_file.pof file
> >
> > ***** High Performance Software Defined Radio Discussion List *****
> >
> > Hi Mike,
> >
> > Sorry to hear you're having trouble.  Here are my suggestions:
> >
> > 1) Run the HPSDSRProgrammer program, under Device select "Hermes", then
> click on the "Hermes Bootloader" tab.
> >
> > 2) Browse to the Angelia_v2.0.rbf file (there is no .rtf file).
> >
> > 3) After putting J17 on your Angelia board, power cycle the Angelia
> board to ensure that things come up properly for programing the
> > EEPROM (ethernet cable connected, of course).
> >
> > 4) Click on "Program"
> >
> > I like your idea of extending the J17 jumper connection on the
> ANAN-100D.  I use a standalone Angelia board here so access isn't a
> > problem for me but I'd certainly extend the connection if I had an
> ANAN-100D.
> >
> > If these steps don't work for you I suggest that we work together via
> direct email (off reflector) so that we will be able to pass
> > screen shots to each other.  That way perhaps we can more easily find
> out what's going on with your particular system.
> >
> > 73,  Joe K5SO
> >
> >
> > On Sep 16, 2013, at 7:31 PM, mstangelo at comcast.net wrote:
> >
> >> Joe,
> >>
> >> I am trying method 2 usingHPSDRProgrammer -- for W5WC and K5SO
> -2012-12-8-Rev 3
> >>
> >> I select Hermes device - Hermes Boot Loader, Browse for the .rtf file
> and select Program
> >>
> >> I then get an Error: cannot open interface (are you running as root).
> Operating system is Windows XP. I'm logged in with my
> > account which is set as administrator.
> >>
> >> I found a 2 pin plug that fits onto J17. I intend to run the cable from
> this plug out a rear vent hole so that I can easily short
> > J17 in the future.
> >>
> >> Mike N2MS
> >
> > _______________________________________________
> > HPSDR Discussion List
> > To post msg: hpsdr at openhpsdr.org
> > Subscription help:
> http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> > HPSDR web page: http://openhpsdr.org
> > Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
> >
>
> _______________________________________________
> HPSDR Discussion List
> To post msg: hpsdr at openhpsdr.org
> Subscription help:
> http://lists.openhpsdr.org/listinfo.cgi/hpsdr-openhpsdr.org
> HPSDR web page: http://openhpsdr.org
> Archives: http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/
>



-- 
I can explain it for you, but I can't comprehend it for you.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.openhpsdr.org/pipermail/hpsdr-openhpsdr.org/attachments/20130917/63a81b86/attachment-0004.htm>